Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Entry and Start System) › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048166 IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Harness or connector

·

ECM

·

Transponder key ECU assembly

·

Telephone transceiver assembly*


DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.



*: w/ Blocking System


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

1. w/o Blocking System


B271007E38
5.406,2.021 6.802,2.427 1.396,0.406 10 false Transponder Key ECU Assembly 5.385,1.844 5.896,2.042 0.51,0.198 10 false G88 1.167,2.167 1.865,2.354 0.698,0.188 10 false ECM 1.792,0.896 2.344,1.083 0.552,0.188 10 false 28*1 1.5,1.01 1.958,1.313 0.458,0.302 10 false IMI 1.177,1.833 1.771,2.021 0.594,0.188 10 false A62*1 5.198,0.906 5.698,1.26 0.5,0.354 10 false 13 5.5,1.021 6.073,1.406 0.573,0.385 10 false EFIO 1.792,1.135 2.344,1.323 0.552,0.188 10 false 16*2 1.177,1.99 1.771,2.177 0.594,0.188 10 false A61*2 0.052,2.156 1.115,2.354 1.063,0.198 10 false *1: for Gasoline 0.052,2.448 0.969,2.615 0.917,0.167 10 false *2: for Diesel


2. w/ Blocking System


B278905E03
1.167,1.854 1.448,2.031 0.281,0.177 10 A62 1.167,2 1.625,2.177 0.458,0.177 10 ECM 5.479,1.01 5.875,1.198 0.396,0.188 10 EFIO 3.646,1.01 4.042,1.198 0.396,0.188 10 BLK4 3.188,1.01 3.583,1.198 0.396,0.188 10 BLK3 1.49,1 1.885,1.188 0.396,0.188 10 IMI 1.813,0.927 2.052,1.104 0.24,0.177 10 28 5.208,0.927 5.5,1.135 0.292,0.208 10 13 4.073,0.927 4.365,1.135 0.292,0.208 10 2 3.031,0.927 3.156,1.135 0.125,0.208 10 8 5.323,1.844 5.708,2.031 0.385,0.188 10 G88 2.865,1.771 3.25,1.958 0.385,0.188 10 G58 5.323,2.021 6.729,2.344 1.406,0.323 10 Transponder Key ECU Assembly 2.865,1.948 4.25,2.292 1.385,0.344 10 Telephone Transceiver Assembly


CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly, telephone transceiver assembly* or ECM is replaced, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.


*: w/ Blocking System



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 61
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B279A is not output
B279A is output



B279A is not output

B279A is output

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Disconnect the A62*1 or A61*2 ECM connector.

*1: for Gasoline

*2: for Diesel



c.

w/ Blocking System:

i.

Disconnect the G58 telephone transceiver assembly connector.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Blocking System (for Gasoline):
Tester Connection Condition Specified Condition
G88-13 (EFIO) - A62-28 (IMI) Always Below 1 Ω
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G88-13 (EFIO) - Body ground Always 10 kΩ or higher

w/o Blocking System (for Diesel):
Tester Connection Condition Specified Condition
G88-13 (EFIO) - A61-16 (IMI) Always Below 1 Ω
A61-16 (IMI) - Body ground Always 10 kΩ or higher
G88-13 (EFIO) - Body ground Always 10 kΩ or higher

w/ Blocking System:
Tester Connection Condition Specified Condition
G88-13 (EFIO) - G58-2 (BLK4) Always Below 1 Ω
G58-8 (BLK3) - A62-28 (IMI) Always Below 1 Ω
G88-13 (EFIO) - Body ground Always 10 kΩ or higher
G58-2 (BLK4) - Body ground Always 10 kΩ or higher
G58-8 (BLK3) - Body ground Always 10 kΩ or higher
A62-28 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 61

Result:
Proceed to
NEXT (w/o Blocking System)
NEXT (w/ Blocking System)



NEXT (w/o Blocking System)

7.CHECK FOR DTC

NEXT (w/ Blocking System)

8.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 61
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B279A is not output
B279A is output (for 2AR-FE)
B279A is output (for 3ZR-FAE)
B279A is output (for 3ZR-FE)
B279A is output (for 1AD-FTV)
B279A is output (for 2AD-FTV)
B279A is output (for 2AD-FHV)



B279A is not output

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B279A is output (for 2AR-FE)

B279A is output (for 3ZR-FAE)

B279A is output (for 3ZR-FE)

B279A is output (for 1AD-FTV)

B279A is output (for 2AD-FTV)

B279A is output (for 2AD-FHV)

8.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A is not output.



Result:
Proceed to
DTC B279A is not output
DTC B279A is output



DTC B279A is not output

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

DTC B279A is output

9.REPLACE ECM
9.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

for 2AR-FE:

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL

for 3ZR-FE:

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
DTC B279A is not output
DTC B279A is output



DTC B279A is not output

END (ECM WAS DEFECTIVE)

DTC B279A is output

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY