Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.12–2013.11
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E269544E02
1.844,0.25 3.135,0.469 1.292,0.219 10 from TAIL Relay 3.896,0.406 4.427,0.604 0.531,0.198 10 PANEL 6,1.073 6.354,1.281 0.354,0.208 10 ILL+ 5.792,3.656 6.167,3.865 0.375,0.208 10 G141 5.813,3.833 7.021,4.208 1.208,0.375 10 Radio and Display Receiver Assembly 3.76,2.271 4.094,2.448 0.333,0.177 10 G8 3.177,2.188 3.479,2.365 0.302,0.177 10 -DP 3.156,0.99 3.448,1.198 0.292,0.208 10 IL+2 3.76,1.094 4.094,1.271 0.333,0.177 10 G8 2.698,1.083 2.958,1.271 0.26,0.188 10 z1 2.698,2.271 2.958,2.458 0.26,0.188 10 z1 2.917,2.656 3.917,3.073 1,0.417 10 Spiral Cable Sub-assembly 0.615,2.604 1.875,2.958 1.26,0.354 10 Steering Pad Switch RH Side 2.729,0.906 2.896,1.073 0.167,0.167 10 5 2.75,2.083 2.917,2.25 0.167,0.167 10 3 3.76,2.073 3.969,2.24 0.208,0.167 10 11 3.781,0.896 4.042,1.073 0.26,0.177 10 13 5.74,1 5.938,1.177 0.198,0.177 10 10 0.583,1.427 1.865,1.771 1.281,0.344 10 Steering Pad Switch LH Side 0.333,3.5 2.365,3.74 2.031,0.24 10 Steering Pad Switch Assembly 6.01,2.365 6.625,2.563 0.615,0.198 10 GND1 5.813,2.229 5.99,2.417 0.177,0.188 10 7

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.


Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio and display receiver assembly. B
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). C



A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
E270420C02
0.208,0.781 0.563,1.01 0.354,0.229 2.073,1.51 2.469,1.865 true 1.073,1.844 1.688,1.531 true 2.531,1.792 2.917,1.979 0.385,0.188 10 false IL+2 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 0.292,0.802 0.604,1 0.313,0.198 10 false G8 0.792,1.771 1.115,1.969 0.323,0.198 10 false -DP
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-13 (IL+2) - Body ground Ignition switch off Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE

NG

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E259248C03
1.51,0.396 1.896,0.594 0.385,0.198 2.271,1.656 2.083,1.354 false 1.271,1.646 1.594,1.365 true 0.146,0.115 0.458,0.271 0.313,0.156 10 *a 1.531,0.417 1.875,0.625 0.344,0.208 10 G141 2.198,1.708 2.75,1.927 0.552,0.219 10 ILL+ 1.063,1.667 1.5,1.865 0.438,0.198 10 GND1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G141-10 (ILL+) - Body ground Ignition switch off Light control switch in the tail or head position 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-7 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR