w/ Multi-information Display (Dot Display Type):
When there is a communication malfunction between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC.
w/ Multi-information Display (Segment Display Type):
When there are communication malfunctions between the ECM and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the ECM stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2799 | Immobiliser Malfunction | Either condition is met (1 trip detection logic*3):
·
A malfunction in the communication or communication lines between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2. ·
A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2. |
·
ID code box (immobiliser code ECU)*1 ·
Certification ECU (smart key ECU assembly)*2 ·
ECM ·
Harness or connector ·
Telephone transceiver assembly*6 |
DTC output confirmation operation (Either condition is met):
·
Within 10 seconds of an engine start operation being performed (with the shift lever in P*4 and the brake pedal*4 or clutch pedal*5 depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds). ·
10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds). |
*1: w/ Multi-information Display (Dot Display Type)
*2: w/ Multi-information Display (Segment Display Type)
*3: Only output while a malfunction is present.
*4: except Manual Transaxle
*5: for Manual Transaxle
*6: w/ Blocking System
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2799 | - |
1. w/o Blocking System
2. w/ Blocking System
When replacing the certification ECU (smart key ECU assembly)*1, ID code box (immobiliser code ECU)*2 or telephone transceiver assembly*3, refer to the Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.*3
*1: w/ Multi-information Display (Segment Display Type)
*2: w/ Multi-information Display (Dot Display Type)
*3: w/ Blocking System
When DTC B2799 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.
Check the vehicle specification.
| Proceed to |
|---|
| w/o Blocking System |
| w/ Blocking System |
w/o Blocking System
w/ Blocking System
*1: w/ Multi-information Display (Dot Display Type)
*2: w/ Multi-information Display (Segment Display Type)
*3: for Gasoline
*4: for Diesel
Disconnect the G44 ID code box (immobiliser code ECU) connector.*1
Disconnect the G82 certification ECU (smart key ECU assembly) connector.*2
Disconnect the A62*3 or A61*4 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G44-3 (EFII) - A62-29 (IMO)*1 | Always | Below 1 Ω |
| G82-14 (EFII) - A62-29 (IMO)*2 | ||
| A62-29 (IMO) - Body ground | Always | 10 kΩ or higher |
| G44-3 (EFII) - Body ground*1 | Always | 10 kΩ or higher |
| G82-14 (EFII) - Body ground*2 | Always | 10 kΩ or higher |
| G44-4 (EFIO) - A62-28 (IMI)*1 | Always | Below 1 Ω |
| G82-13 (EFIO) - A62-28 (IMI)*2 | ||
| A62-28 (IMI) - Body ground | Always | 10 kΩ or higher |
| G44-4 (EFIO) - Body ground*1 | Always | 10 kΩ or higher |
| G82-13 (EFIO) - Body ground*2 | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G44-3 (EFII) - A61-15 (IMO)*1 | Always | Below 1 Ω |
| G82-14 (EFII) - A61-15 (IMO)*2 | ||
| A61-15 (IMO) - Body ground | Always | 10 kΩ or higher |
| G44-3 (EFII) - Body ground*1 | Always | 10 kΩ or higher |
| G82-14 (EFII) - Body ground*2 | Always | 10 kΩ or higher |
| G44-4 (EFIO) - A61-16 (IMI)*1 | Always | Below 1 Ω |
| G82-13 (EFIO) - A61-16 (IMI)*2 | ||
| A61-16 (IMI) - Body ground | Always | 10 kΩ or higher |
| G44-4 (EFIO) - Body ground*1 | Always | 10 kΩ or higher |
| G82-13 (EFIO) - Body ground*2 | Always | 10 kΩ or higher |
*1: w/ Multi-information Display (Dot Display Type)
*2: w/ Multi-information Display (Segment Display Type)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reregister the ECU communication ID.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
| Proceed to |
|---|
| B2799 is not output |
| B2799 is output |
| Other DTCs are output |
B2799 is not output
B2799 is output
Other DTCs are output
Temporarily replace the ECM with a new one.
for 2AR-FE:
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FAE:
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE:
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
for 1AD-FTV:
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2AD-FTV:
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2AD-FHV:
Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Reregister the ECU communication ID.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
DTC B2799 is not output.
| Proceed to |
|---|
| OK |
| NG (w/ Multi-information Display [Dot Display Type]) |
| NG (w/ Multi-information Display [Segment Display Type]) |
OK
NG (w/ Multi-information Display [Dot Display Type])
NG (w/ Multi-information Display [Segment Display Type])
Disconnect the A62 ECM connector.
Disconnect the G58 telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-29 (IMO) - G58-7 (BLK2) | Always | Below 1 Ω |
| A62-29 (IMO) - Body ground | Always | 10 kΩ or higher |
| G58-7 (BLK2) - Body ground | Always | 10 kΩ or higher |
| A62-28 (IMI) - G58-8 (BLK3) | Always | Below 1 Ω |
| A62-28 (IMI) - Body ground | Always | 10 kΩ or higher |
| G58-8 (BLK3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G82 certification ECU (smart key ECU assembly) connector.
Disconnect the G58 telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-14 (EFII) - G58-1 (BLK1) | Always | Below 1 Ω |
| G82-14 (EFII) - Body ground | Always | 10 kΩ or higher |
| G58-1 (BLK1) - Body ground | Always | 10 kΩ or higher |
| G82-13 (EFIO) - G58-2 (BLK4) | Always | Below 1 Ω |
| G82-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
| G58-2 (BLK4) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reregister the ECU communication ID.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
| Proceed to |
|---|
| B2799 is not output |
| B2799 is output |
| Other DTCs are output |
B2799 is not output
B2799 is output
Other DTCs are output
Temporarily replace the telephone transceiver assembly with a new or known good one.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Reregister the ECU communication ID.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
| Proceed to |
|---|
| B2799 is not output |
| B2799 is output |
B2799 is not output
B2799 is output