Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Entry and Start System) › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048164 IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

·

w/ Multi-information Display (Dot Display Type)

When the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high, the ECM stores this DTC.

·

w/ Multi-information Display (Segment Display Type)

When the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM stores this DTC.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 is stuck high (1 trip detection logic*3).
·

Harness or connector

·

ID code box (immobiliser code ECU)*1

·

Certification ECU (smart key ECU assembly)*2

·

ECM

·

Telephone transceiver assembly*4


DTC output confirmation operation:

Turn the engine switch on (IG) and wait 10 seconds.



*1: w/ Multi-information Display (Dot Display Type)

*2: w/ Multi-information Display (Segment Display Type)

*3: Only output while a malfunction is present.

*4: w/ Blocking System


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

1. w/o Blocking System



B278904E04
1.167,1.646 1.667,1.813 0.5,0.167 10 false A62*3 1.167,1.802 1.625,1.979 0.458,0.177 10 false A61*4 5.49,0.813 5.885,1 0.396,0.188 10 false EFIO 5.49,3.167 5.885,3.354 0.396,0.188 10 false EFIO 1.51,0.823 1.906,1.01 0.396,0.188 10 false IMI 1.813,0.719 2.51,0.896 0.698,0.177 10 false 28*3 4.427,0.719 4.76,1.031 0.333,0.313 10 false *2 5.229,0.729 5.521,0.938 0.292,0.208 10 false 13 5.271,3.094 5.427,3.302 0.156,0.208 10 false 4 5.052,1.583 5.438,1.771 0.385,0.188 10 false G82 5.052,3.885 5.438,4.073 0.385,0.188 10 false G44 5.052,1.76 6.594,2.083 1.542,0.323 10 false Certification ECU (Smart Key ECU Assembly) 5.052,4.063 6.635,4.469 1.583,0.406 10 false ID Code Box (Immobiliser Code ECU) 0.167,2.906 3.396,3.104 3.229,0.198 10 false *1: w/ Multi-information Display (Dot Display Type) 0.177,3.25 3.74,3.427 3.563,0.177 10 false *2: w/ Multi-information Display (Segment Display Type) 3.75,2.01 4.042,2.281 0.292,0.271 10 false *1 1.813,0.927 2.51,1.104 0.698,0.177 10 false 16*4 1.167,1.958 1.625,2.135 0.458,0.177 10 false ECM 0.188,3.542 3.75,3.719 3.563,0.177 10 false *3: for Gasoline 0.188,3.823 3.75,4 3.563,0.177 10 false *4: for Diesel

2. w/ Blocking System


B278905E02
1.167,1.854 1.448,2.031 0.281,0.177 10 A62 1.167,2 1.625,2.177 0.458,0.177 10 ECM 5.479,1.01 5.875,1.198 0.396,0.188 10 EFIO 3.646,1.01 4.042,1.198 0.396,0.188 10 BLK4 3.188,1.01 3.583,1.198 0.396,0.188 10 BLK3 1.49,1 1.885,1.188 0.396,0.188 10 IMI 1.813,0.927 2.052,1.104 0.24,0.177 10 28 5.208,0.927 5.5,1.135 0.292,0.208 10 13 4.073,0.927 4.365,1.135 0.292,0.208 10 2 3.031,0.927 3.156,1.135 0.125,0.208 10 8 5.042,1.771 5.427,1.958 0.385,0.188 10 G82 2.865,1.771 3.25,1.958 0.385,0.188 10 G58 5.042,1.948 6.583,2.271 1.542,0.323 10 Certification ECU (Smart Key ECU Assembly) 2.865,1.948 4.25,2.292 1.385,0.344 10 Telephone Transceiver Assembly


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the certification ECU (smart key ECU assembly)*1, ID code box (immobiliser code ECU)*2 or telephone transceiver assembly*3, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."

·

When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.*3


*1: w/ Multi-information Display (Segment Display Type)

*2: w/ Multi-information Display (Dot Display Type)

*3: w/ Blocking System



HINT:

When DTC B279A and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

If DTCs other than DTC B279A are output, troubleshoot those DTCs first.



Result:
Proceed to
DTC B279A is not output
DTC B279A and other DTCs are output



DTC B279A is not output

3.CHECK CONNECTION OF CONNECTOR

DTC B279A and other DTCs are output

3.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM, ID code box (immobiliser code ECU)*1, certification ECU (smart key ECU assembly)*2 and telephone transceiver assembly*3.

*1: w/ Multi-information Display (Dot Display Type)

*2: w/ Multi-information Display (Segment Display Type)

*3: w/ Blocking System


OK:

Connectors are properly connected.



Result:
Proceed to
OK (w/o Blocking System)
OK (w/ Blocking System)
NG



OK (w/o Blocking System)

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] OR CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ECM)

OK (w/ Blocking System)

15.CHECK HARNESS AND CONNECTOR (ECM - TELEPHONE TRANSCEIVER ASSEMBLY)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] OR CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ECM)

*1: w/ Multi-information Display (Dot Display Type)

*2: w/ Multi-information Display (Segment Display Type)

*3: for Gasoline

*4: for Diesel


a.

Disconnect the G44 ID code box (immobiliser code ECU) connector.*1


b.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.*2


c.

Disconnect the A62*3 or A61*4 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Gasoline
Tester Connection Condition Specified Condition
G44-4 (EFIO) - A62-28 (IMI)*1 Always Below 1 Ω
G82-13 (EFIO) - A62-28 (IMI)*2
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground*1 Always 10 kΩ or higher
G82-13 (EFIO) - Body ground*2 Always 10 kΩ or higher

for Diesel
Tester Connection Condition Specified Condition
G44-4 (EFIO) - A61-16 (IMI)*1 Always Below 1 Ω
G82-13 (EFIO) - A61-16 (IMI)*2
A61-16 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground*1 Always 10 kΩ or higher
G82-13 (EFIO) - Body ground*2 Always 10 kΩ or higher


*1: w/ Multi-information Display (Dot Display Type)

*2: w/ Multi-information Display (Segment Display Type)



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Gasoline
Tester Connection Condition Specified Condition
A62-28 (IMI) - Body ground Always Below 1 V
G44-4 (EFIO) - Body ground*1 Always Below 1 V
G82-13 (EFIO) - Body ground*2 Always Below 1 V

for Diesel
Tester Connection Condition Specified Condition
A61-16 (IMI) - Body ground Always Below 1 V
G44-4 (EFIO) - Body ground*1 Always Below 1 V
G82-13 (EFIO) - Body ground*2 Always Below 1 V


*1: w/ Multi-information Display (Dot Display Type)

*2: w/ Multi-information Display (Segment Display Type)



Result:
Proceed to
OK (w/ Multi-information Display [Dot Display Type])
OK (w/ Multi-information Display [Segment Display Type])
NG



OK (w/ Multi-information Display [Dot Display Type])

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

OK (w/ Multi-information Display [Segment Display Type])

10.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.REGISTER RECOGNITION CODES
6.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
DTC B279A is not output
DTC B279A is output (for 2AR-FE)
DTC B279A is output (for 3ZR-FAE)
DTC B279A is output (for 3ZR-FE)
DTC B279A is output (for 1AD-FTV)
DTC B279A is output (for 2AD-FTV)
DTC B279A is output (for 2AD-FHV)



DTC B279A is not output

END (ID CODE BOX [IMMOBILISER CODE ECU] WAS DEFECTIVE)

DTC B279A is output (for 2AR-FE)

DTC B279A is output (for 3ZR-FAE)

DTC B279A is output (for 3ZR-FE)

DTC B279A is output (for 1AD-FTV)

DTC B279A is output (for 2AD-FTV)

DTC B279A is output (for 2AD-FHV)

10.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.REGISTER RECOGNITION CODES
11.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

12.REGISTER ECU COMMUNICATION ID
12.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
13.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

14.CHECK FOR DTC
14.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
DTC B279A is not output
DTC B279A is output (for 2AR-FE)
DTC B279A is output (for 3ZR-FAE)
DTC B279A is output (for 3ZR-FE)
DTC B279A is output (for 1AD-FTV)
DTC B279A is output (for 2AD-FTV)
DTC B279A is output (for 2AD-FHV)



DTC B279A is not output

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

DTC B279A is output (for 2AR-FE)

DTC B279A is output (for 3ZR-FAE)

DTC B279A is output (for 3ZR-FE)

DTC B279A is output (for 1AD-FTV)

DTC B279A is output (for 2AD-FTV)

DTC B279A is output (for 2AD-FHV)

15.CHECK HARNESS AND CONNECTOR (ECM - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the A62 ECM connector.


b.

Disconnect the G58 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-28 (IMI) - G58-8 (BLK3) Always Below 1 Ω
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G58-8 (BLK3) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-28 (IMI) - Body ground Always Below 1 V
G58-8 (BLK3) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - TELEPHONE TRANSCEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G58 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-13 (EFIO) - G58-2 (BLK4) Always Below 1 Ω
G82-13 (EFIO) - Body ground Always 10 kΩ or higher
G58-2 (BLK4) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-13 (EFIO) - Body ground Always Below 1 V
G58-2 (BLK4) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

17.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Temporarily replace the telephone transceiver assembly with a new or known good one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

18.REGISTER ECU COMMUNICATION ID
18.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

19.CLEAR DTC
19.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

20.CHECK FOR DTC
20.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
DTC B279A is not output
DTC B279A is output



DTC B279A is not output

END (TELEPHONE TRANSCEIVER ASSEMBLY WAS DEFECTIVE)

DTC B279A is output

10.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)