Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.12–2015.10
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2 to use for adjusting the vehicle position on the display.

*1: except Manual Transaxle

*2: for Manual Transaxle


WIRING DIAGRAM

E270422E02
0.292,0.875 1.521,1.063 1.229,0.188 10 from GAUGE Fuse 2.917,1.208 3.26,1.375 0.344,0.167 10 B36 2.927,2.906 3.271,3.073 0.344,0.167 10 B35 2.938,1.396 4.25,1.75 1.313,0.354 10 Park/Neutral Position Switch Assembly*1 2.927,3.063 4.281,3.417 1.354,0.354 10 Back-up Light Switch Assembly*2 3.094,0.792 3.438,0.958 0.344,0.167 10 RB 3.781,0.792 4.125,0.958 0.344,0.167 10 RL 2.938,0.792 3.281,0.958 0.344,0.167 10 1 4.021,0.781 4.365,0.948 0.344,0.167 10 2 4.021,2.5 4.365,2.667 0.344,0.167 10 1 2.938,2.49 3.281,2.656 0.344,0.167 10 2 5.25,0.781 5.594,0.948 0.344,0.167 10 2 5.448,0.875 5.792,1.042 0.344,0.167 10 REV 5.385,1.5 5.729,1.667 0.344,0.167 10 G143 5.406,1.688 6.615,2.073 1.208,0.385 10 Radio and Display Receiver Assembly 0.177,3.063 2.354,3.26 2.177,0.198 10 *1: except Manual Transaxle 0.177,3.375 2.354,3.573 2.177,0.198 10 *2: for Manual Transaxle

PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E270655

Enter the "Function Check/Setting I" mode and select "Vehicle Signal".

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (REVERSE SIGNAL)
2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (REVERSE SIGNAL)
a.
E140414C08
1.427,0.448 2.031,0.729 0.604,0.281 0.917,1.396 0.635,1.208 0.635,1.208 0.521,1.208 false 0.063,0.063 0.302,0.25 0.24,0.188 10 *a 1.573,0.5 1.938,0.688 0.365,0.188 10 G143 0.156,1.135 0.49,1.302 0.333,0.167 10 REV
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G143-2 (REV) - Body ground Ignition switch ON, shift lever in R 11 to 14 V
G143-2 (REV) - Body ground Ignition switch ON, shift lever any position other than in R Below 1 V



Result:
Proceed to
OK
NG (except Manual Transaxle)
NG (for Manual Transaxle)



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG (except Manual Transaxle)

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG (for Manual Transaxle)

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the B36 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-2 (REV) - B36-2 (RL) Always Below 1 Ω
G143-2 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
E270424C01
1.479,0.281 1.885,0.51 0.406,0.229 1.073,1.771 1.26,1.771 1.26,1.771 1.604,1.135 true 1.542,0.313 2,0.51 0.458,0.198 10 B36 0.823,1.698 1.281,1.896 0.458,0.198 10 RB 0.104,0.083 0.563,0.281 0.458,0.198 10 *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B36-1 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the B35 back-up light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-2 (REV) - B35-1 Always Below 1 Ω
G143-2 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)
a.
E270423C01
0.844,0.396 1.24,0.625 0.396,0.229 0.115,0.146 0.427,0.344 0.313,0.198 10 *a 0.906,0.427 1.219,0.625 0.313,0.198 10 B35
*a Front view of wire harness connector
(to Back-up Light Switch Assembly)


Disconnect the back-up light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B35-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR