Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0051076 SFI SYSTEM(w/o Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stored the DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0420 Catalyst System Efficiency Below Threshold (Bank 1) The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (sensor 1)

·

Heated oxygen sensor (sensor 2)

·

Exhaust manifold converter sub-assembly (TWC: Front catalyst) and front No. 2 exhaust pipe sub-assembly (TWC: Rear catalyst)


Comes on DTC stored

CATALYST LOCATION

A290282C01
0.875,2.906 1.417,1.75 1.417,1.75 1.667,1.75 false 1.531,2.552 2.083,2.167 2.083,2.167 2.417,2.167 false 0.583,2.5 1.125,1.344 1.125,1.344 1.375,1.344 false 2.167,3.25 2.583,4.083 2.583,4.083 2.917,4.083 false 4.125,2.49 4.667,1.333 4.667,1.333 4.917,1.333 false 6.417,1.583 6.833,2.75 6.833,2.75 6.583,2.75 false 1.083,3.75 1.5,4.333 1.5,4.333 1.833,4.333 false 1.75,1.667 1.979,1.833 0.229,0.167 10 false *1 2.5,2.083 2.729,2.25 0.229,0.167 10 false *2 1.438,1.25 1.667,1.417 0.229,0.167 10 false *3 3,4 3.229,4.167 0.229,0.167 10 false *4 5,1.25 5.25,1.417 0.25,0.167 10 false *5 6.354,2.667 6.583,2.833 0.229,0.167 10 false *6 1.854,4.25 2.083,4.417 0.229,0.167 10 false *7
*1 Air Fuel Ratio Sensor (Sensor 1) *2 Heated Oxygen Sensor (Sensor 2)
*3 Exhaust Manifold Converter Sub-assembly
(TWC: Front Catalyst)
*4 Front No. 2 Exhaust Pipe Sub-assembly
(TWC: Rear Catalyst)
*5 Center Exhaust Pipe Assembly *6 Tail Exhaust Pipe Assembly
*7 Front Exhaust Pipe Sub-assembly - -


NOTICE:

Replace the exhaust manifold converter sub-assembly (*3) and the front No. 2 exhaust pipe sub-assembly (*4) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor *1 and heated oxygen sensor *2)


MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Heated oxygen sensor
Required Sensors/Components (Related) Intake air temperature sensor
Mass air flow meter sub-assembly
Crankshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Catalyst Deterioration
Battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [570 mmHg(abs)] or higher
Idling Off
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 80%
Shift position 5th or higher
All of the following conditions are met -
Mass air flow rate 2.5 gm/sec or more, and less than 40 gm/sec.
Front catalyst temperature (estimated) 540°C (1004°F) or higher, and less than 800°C (1472°F)
Rear catalyst temperature (estimated) 300°C (572°F) or higher, and less than 800°C (1472°F)

Catalyst Deterioration for Brazil OBD Phase 2 Models
Battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [570 mmHg(abs)] or higher
Idling Off
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 90%
Shift position 3rd or higher
All of the following conditions are met -
Mass air flow rate 1.5 gm/sec or more, and less than 75 gm/sec.
Front catalyst temperature (estimated) 540°C (1004°F) or higher, and less than 880°C (1616°F)
Rear catalyst temperature (estimated) 380°C (716°F) or higher, and less than 770°C (1418°F)

HINT:

The estimated catalyst temperature can be read in the Data List using the GTS.


CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A283969E26
1.833,0.333 1.667,0.333 1.667,0.333 1.302,0.865 false 0.771,1.156 1.5,1.313 0.729,0.156 10 60 km/h 0.917,2.167 1.333,2.427 0.417,0.26 10 Idling 0.167,2.5 1.333,2.75 1.167,0.25 10 Ignition Switch off 1.417,2.729 2.271,3 0.854,0.271 10 Warming up 2.365,2.75 3.083,3.083 0.719,0.333 10 10 minutes or more 4.156,2.729 4.917,3.083 0.76,0.354 10 10 minutes or more 1.917,0.25 3.469,0.427 1.552,0.177 10 Between 75 to 100 km/h 1.667,2.083 1.896,2.26 0.229,0.177 10 [A] 2.594,1 2.917,1.177 0.323,0.177 10 [B]* 3.156,3.156 3.385,3.333 0.229,0.177 10 [C] 6.76,3.167 6.99,3.344 0.229,0.177 10 [H] 3.458,2.083 3.667,2.26 0.208,0.177 10 [D] 6.146,0.583 6.5,0.76 0.354,0.177 10 [G]* 4.333,0.99 4.698,1.167 0.365,0.177 10 [E]* 5.01,3.156 5.208,3.333 0.198,0.177 10 [F] 3.396,2.729 4,3.083 0.604,0.354 10 Warming up 5.917,2.75 6.729,3.135 0.813,0.385 10 10 minutes or more 0.083,3.354 4.583,3.583 4.5,0.229 10 *: Drive the vehicle while keeping the engine load as constant as possible

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


9.

Turn the ignition switch off and wait for at least 30 seconds [C].

10.

Turn the ignition switch to ON and turn the GTS on.

11.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].

12.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


13.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


16.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness [H].

17.

Input the DTC: P0420.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A292989E04
4.875,3.094 4.875,3.344 false 5.177,3.094 5.177,3.344 false 4.875,3.344 5.458,3.344 false 0.583,0.688 1.51,0.927 0.927,0.24 10 Engine Speed 0.865,1.031 1.479,1.26 0.615,0.229 10 3000 rpm 0.865,1.573 1.542,1.771 0.677,0.198 10 2000 rpm 1.104,2.542 1.594,2.802 0.49,0.26 10 Idling 0.365,2.802 1.521,3 1.156,0.198 10 Ignition Switch off 2.104,3.167 2.958,3.396 0.854,0.229 10 Warming up 3.333,3.167 4.531,3.385 1.198,0.219 10 At least 3 minutes 5.5,3.26 6.198,3.51 0.698,0.25 10 2 seconds 4.865,3.396 5.333,3.583 0.469,0.188 10 Check 6.615,2.76 6.958,3 0.344,0.24 10 Time 1.646,2.656 1.885,2.896 0.24,0.24 10 (a) 2.094,2.417 2.354,2.677 0.26,0.26 10 (b) 3.625,0.865 3.854,1.094 0.229,0.229 10 (c) 4.802,0.875 5.052,1.156 0.25,0.281 10 (d) 5.104,1.458 5.323,1.729 0.219,0.271 10 (d)

(a) Connect the GTS to the DLC3.

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.

(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(d) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS.


HINT:
·

If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume Active Test using the GTS.

·

If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter [TWC]) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).


A199479E09
0.255,0.104 4.136,0.267 3.882,0.163 10 Voltage output when active air fuel ratio control not performed: 2.433,0.532 3.565,0.695 1.132,0.163 10 Normal Catalyst 4.759,0.546 6.130,0.729 1.371,0.184 10 Deteriorated Catalyst 2.405,2.991 3.276,3.185 0.871,0.194 10 10 seconds 4.955,3.005 5.785,3.167 0.830,0.163 10 10 seconds 0.049,0.763 1.332,1.551 1.283,0.788 10 Waveform of Air Fuel Ratio Sensor in front of Three-way Catalytic Converter 1.465,0.784 1.810,0.926 0.345,0.142 10 3.4 V 1.465,1.204 1.810,1.346 0.345,0.142 10 3.1 V 1.459,2.053 1.810,2.256 0.351,0.204 10 1.0 V 1.536,2.724 1.811,2.950 0.275,0.225 10 0 V 0.038,2.164 1.374,2.952 1.336,0.788 10 Waveform of Heated Oxygen Sensor behind Three-way Catalytic Converter


CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be the cause. Perform troubleshooting by following the procedure for P0171 (System Too Lean) and P0172 (System Too Rich).

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0420 is output A
DTC P0420 and other DTCs are output B


HINT:

If any DTCs other than P0420 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Ptrl AF Control / AFS Voltage B1S1 and O2S B1S2.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
O2S B1S2
50004 234 2 35,44

f.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).


g.

Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of -12.5% and +12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result:
Status AFS Voltage B1S1 Status O2S B1S2 Actual air fuel ratio, air fuel ratio sensor and heated oxygen sensor condition Misfire Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal -
·

Three-way catalytic converter

·

Gas leak from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


Lean/Rich Lean Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


Lean Lean Actual air fuel ratio lean May occur
·

Extremely rich or lean actual air fuel ratio

·

Gas leak from exhaust system


D
Rich Rich Actual air fuel ratio rich -
·

Extremely rich or lean actual air fuel ratio

·

Gas leak from exhaust system




Lean: During Control the Injection Volume, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.



A

3.CHECK FOR EXHAUST GAS LEAK

B

8.REPLACE AIR FUEL RATIO SENSOR

C

9.CHECK FOR EXHAUST GAS LEAK

D

11.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY (TWC: REAR CATALYST)

NG

5.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the front No. 2 exhaust pipe sub-assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst).

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>REMOVAL


b.

Replace the front No. 2 exhaust pipe sub-assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>EXHAUST PIPE>REMOVAL


Result:
Proceed to
NEXT



NEXT

END

5.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
a.

Repair or replace exhaust gas leak point.

HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


k.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0420 is output A
DTC is not output
(No pending DTCs output)
B




A

7.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY (TWC: REAR CATALYST)

B

END

7.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the front No. 2 exhaust pipe sub-assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst).

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>REMOVAL


b.

Replace the front No. 2 exhaust pipe sub-assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>EXHAUST PIPE>REMOVAL


Result:
Proceed to
NEXT



NEXT

END

8.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
9.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

10.REPLACE HEATED OXYGEN SENSOR

NG

5.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
10.REPLACE HEATED OXYGEN SENSOR
a.

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
11.CHECK FOR EXHAUST GAS LEAK
a.

Check the exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

12.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

5.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
12.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Procedure.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>P0171


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)