Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0051076 SFI SYSTEM(w/o Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTD, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch ON
(b) STP signal off when ST1- signal off
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

IG2 relay

·

ECM


- DTC stored

WIRING DIAGRAM

A290316
6.25,0.365 6.583,0.531 0.333,0.167 10 false STP 6.25,1.156 6.583,1.323 0.333,0.167 10 false ST1- 5.948,1.156 6.198,1.323 0.25,0.167 10 false 24 5.948,0.365 6.198,0.531 0.25,0.167 10 false 11 6.417,2.75 6.75,2.917 0.333,0.167 10 false ECM 5.531,0.365 5.698,0.531 0.167,0.167 10 false 1 5.521,1.156 5.688,1.323 0.167,0.167 10 false 3 4.833,1.667 5.083,1.833 0.25,0.167 10 false A5 4.833,1.813 6,2.167 1.167,0.354 10 false Stop Light Switch Assembly 4.688,1.156 4.854,1.323 0.167,0.167 10 false 4 4.688,0.365 4.854,0.531 0.167,0.167 10 false 2 4.052,0.635 4.469,0.802 0.417,0.167 10 false STOP 4.125,1.417 4.458,1.583 0.333,0.167 10 false IGN 3.688,1.156 3.854,1.323 0.167,0.167 10 false 5 2.896,1.156 3.073,1.323 0.177,0.167 10 false 3 2.896,1.781 3.063,1.948 0.167,0.167 10 false 1 3.688,1.792 3.854,1.958 0.167,0.167 10 false 2 3.25,2.25 3.583,2.417 0.333,0.167 10 false IG2 0.646,0.635 0.979,0.802 0.333,0.167 10 false ALT 0.667,1.417 1,1.583 0.333,0.167 10 false IG2 0.635,2.063 0.969,2.229 0.333,0.167 10 false AM2 1.198,1.75 1.365,1.917 0.167,0.167 10 false 4 2.271,1.75 2.438,1.917 0.167,0.167 10 false 3 1.375,1.75 1.708,1.917 0.333,0.167 10 false AM2 1.979,1.75 2.313,1.917 0.333,0.167 10 false IG2 1.333,2.333 1.667,2.5 0.333,0.167 10 false G4 1.333,2.5 2.333,2.854 1,0.354 10 false Ignition Switch Assembly*1 1.833,3.365 2.25,3.531 0.417,0.167 10 false IG2D 2.229,3.271 2.396,3.438 0.167,0.167 10 false 9 1.167,3.833 1.5,4 0.333,0.167 10 false G82 1.167,4 2.917,4.417 1.75,0.417 10 false Certification ECU (Smart key ECU Assembly)*2 0.583,3.833 1.083,4.083 0.5,0.25 10 false Battery 4.75,3.552 6.698,3.75 1.948,0.198 10 false *1: w/o Entry and Start System 4.75,3.927 6.667,4.104 1.917,0.177 10 false *2: w/ Entry and Start System 6.417,2.583 6.75,2.75 0.333,0.167 10 false A62 0.427,2.729 1.031,2.906 0.604,0.177 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch assembly conditions can be checked using the GTS.

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Throttle / Stop Light Switch and ST1.

5.

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
A203090
0.354,1.833 0.75,2.094 0.396,0.26 0.333,0.198 0.552,0.417 0.219,0.219 10 *a 0.458,1.885 0.729,2.052 0.271,0.167 10 A5
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH ASSEMBLY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
A203090
0.354,1.833 0.75,2.094 0.396,0.26 0.333,0.198 0.552,0.417 0.219,0.219 10 *a 0.458,1.885 0.729,2.052 0.271,0.167 10 A5
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A5-4 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (ST2 RELAY - STOP LIGHT SWITCH ASSEMBLY)
3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)
a.

Disconnect the ECM connector.

A256080C26
4.344,0.833 4.74,1.073 0.396,0.24 6.021,0.854 5.229,1.552 false 6.021,0.927 5.813,1.573 false 1.156,1.438 1.333,1.615 0.177,0.177 10 *a 2.958,1.438 3.135,1.615 0.177,0.177 10 *b 4.604,0.094 4.781,0.271 0.177,0.177 10 *c 4.417,0.875 4.76,1.031 0.344,0.156 10 A62 5.677,1.583 6.01,1.729 0.333,0.146 10 ST1- 5.094,1.573 5.385,1.719 0.292,0.146 10 STP
*a Brake Pedal Depressed *b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)
- -



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-24 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
Brake pedal depressed Below 1.5 V
A62-11 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

5.CHECK HARNESS AND CONNECTOR (ST2 RELAY - STOP LIGHT SWITCH ASSEMBLY)
a.

Remove the IG2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 relay terminal 5 - A5-4 Always Below 1 Ω
IG2 relay terminal 5 or A5-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR