Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0051076 SFI SYSTEM(w/o Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  


DESCRIPTION

HINT:
·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.



The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, and therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A234900E19
1.615,2.969 0.979,2.49 false 1.823,2.969 2.094,2.667 false 2.927,1.76 3.521,0.729 false 3.052,1.792 3.615,1.427 false 3.208,2.188 3.698,1.781 false 2.854,2.396 3.583,2.198 3.583,2.198 3,2.396 false 3.063,2.469 3.49,2.74 false 0.156,3.271 0.99,3.615 0.833,0.344 10 Exhaust Gas 0.438,2.375 0.979,2.708 0.542,0.333 10 Element 2.115,2.563 2.51,2.865 0.396,0.302 10 Cover 1.125,3.406 1.271,3.604 0.146,0.198 10 A 2.01,3.406 2.156,3.604 0.146,0.198 10 A 3.552,0.646 4.708,1.292 1.156,0.646 10 Solid Electrolyte (Zirconia Element) 3.625,1.313 4.448,1.615 0.823,0.302 10 Alumina 3.719,1.708 4.708,1.99 0.99,0.281 10 Heater 3.604,2.125 5.021,2.469 1.417,0.344 10 Platinum Electrode 3.51,2.646 4.521,2.99 1.01,0.344 10 Atmospheric Air 2.583,3.167 3.75,3.531 1.167,0.365 10 A-A Cross Section 5.677,3.125 6.573,3.469 0.896,0.344 10 Air Fuel Ratio 5.104,0.667 6.969,1.25 1.865,0.583 10 ECM Monitored Air Fuel Ratio Sensor Voltage

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) Either of the following conditions (A) or (B) met:
(A)

Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):

1.

Air fuel ratio sensor voltage is higher than 3.8 V.

2.

Heated oxygen sensor voltage is 0.21 V or higher.



(B)

While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds (2 trip detection logic).


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on DTC stored
P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) Either of the following conditions (A) or (B) is met:
(A)

Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):

1.

Air fuel ratio sensor voltage is less than 2.8 V.

2.

Heated oxygen sensor voltage is less than 0.69 V.



(B)

While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.7 mA for 3 seconds (2 trip detection logic).


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on DTC stored

HINT:
·

When any of these DTCs is stored, check the air fuel ratio sensor voltage output by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Ptrl AF Control / AFS Voltage B1S1.

·

Short-term fuel trim values can also be read using the GTS.

·

The ECM regulates the voltages at the A1A+ and A1A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the GTS.

·

If an air fuel ratio sensor malfunction is detected, the ECM stores a DTC.



MONITOR DESCRIPTION

Sensor Voltage Detection Monitor

Under air fuel ratio feedback control, If the air fuel ratio sensor output voltage is below 2.8 V (very rich condition) for 5 seconds despite the heated oxygen sensor output voltage being below 0.69 V, the ECM stores DTC P2196. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the heated oxygen sensor output voltage being 0.21 V or higher, DTC P2195 is stored.


Sensor Current Detection Monitor

A rich air fuel mixture causes a low air fuel ratio sensor current, and a lean air fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.

If the air fuel ratio sensor output is 2.2 mA or higher for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and stores DTC P2195 (stuck on high side). If the air fuel ratio sensor output is below 0.7 mA for more than 3 seconds of cumulative time, the ECM stores DTC P2196 (stuck on low side).


A293209E02
2.385,2.292 2.229,1.635 2.229,1.635 2.406,1.635 false 4.354,2.292 4.24,1.615 4.24,1.615 4.427,1.615 false 5.76,2.292 5.688,1.594 5.688,1.594 5.875,1.594 false 0.177,0.198 3.135,0.406 2.958,0.208 10 Air Fuel Ratio Sensor Current Monitor 3.01,0.438 6.563,0.625 3.552,0.188 10 Cumulative Time "t" = t1 + t2 = 3 seconds or more 0.51,1.094 1.302,1.344 0.792,0.25 10 Fuel-cut 0.406,2.167 2.229,2.385 1.823,0.219 10 Sensor Current (mA) 0.448,2.823 2.271,3.042 1.823,0.219 10 High Side Threshold 0.479,3.479 2.302,3.698 1.823,0.219 10 Low Side Threshold 2.344,3.698 4.167,3.917 1.823,0.219 10 3 seconds or more 2.323,4.26 4.146,4.479 1.823,0.219 10 Normal Sensor Output 4.646,4.271 6.469,4.49 1.823,0.219 10 Abnormal Sensor Output 6.438,4.281 7.156,4.563 0.719,0.281 10 Time 2.448,1.531 4.271,1.75 1.823,0.219 10 Delay (3 seconds) 4.479,1.521 5.677,1.813 1.198,0.292 10 Delay (3 seconds) 5.958,1.51 7.156,1.802 1.198,0.292 10 Delay (3 seconds) 6.042,3.813 6.76,4.094 0.719,0.281 10 t2 4.698,3.802 5.417,4.083 0.719,0.281 10 t1 1.396,0.938 3.219,1.156 1.823,0.219 10 ON 1.396,1.229 2.094,1.594 0.698,0.365 10 OFF

MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Required Sensors/Components (Related) Heated oxygen sensor
Frequency of Operation Continuous: Sensor voltage detection monitor
Once per driving cycle: Sensor current detection monitor
Duration 5 seconds: Sensor voltage detection monitor
3 seconds: Sensor current detection monitor

TYPICAL ENABLING CONDITIONS

P2195 and P2196: Sensor Voltage Detection Monitor
Time after engine start 30 seconds or more
Fuel system status Closed loop

P2195 and P2196: Sensor Current Detection Monitor
Battery voltage 11 V or higher
Atmospheric pressure 76 kPa(abs) [570 mmHg(abs)] or higher
Air fuel ratio sensor status Activated
Engine coolant temperature 75°C (167°F) or higher
Continuous time of fuel cut 3 seconds or more, and less than 10 seconds

TYPICAL MALFUNCTION THRESHOLDS

P2195: Sensor Voltage Detection Monitor (Lean Side Malfunction)
Heated oxygen sensor voltage 0.21 V or higher
Air fuel ratio sensor voltage Higher than 3.8 V

P2196: Sensor Voltage Detection Monitor (Rich Side Malfunction)
Heated oxygen sensor voltage Less than 0.69 V
Air fuel ratio sensor voltage Less than 2.8 V

P2195: Sensor Current Detection Monitor (High Side Malfunction)
Air fuel ratio sensor current 2.2 mA or higher

P2196: Sensor Current Detection Monitor (Low Side Malfunction)
Air fuel ratio sensor current Less than 0.7 mA

CONFIRMATION DRIVING PATTERN

A293210E02
2.469,1.51 2.917,0.76 2.917,0.76 2.708,0.76 false 4.438,1.521 5.052,1.521 false 4.177,0.833 4.896,1.781 false 5.927,0.625 5.49,1.76 false 5.385,2.198 6.396,2.198 false 4.958,2.948 5.115,2.948 5.115,2.948 5.063,2.729 false 5.385,3.156 5.615,3.156 5.615,3.156 5.5,2.74 false 3.958,3.354 4.365,3.563 false 0.031,0.25 3.031,0.51 3,0.26 10 Engine Coolant Temperature: 75°C or higher 1.083,0.677 2.844,1.031 1.76,0.354 10 Between 60 and 120 km/h 0.75,2.281 1.302,2.698 0.552,0.417 10 Idling 1.292,2.802 2.208,3.24 0.917,0.438 10 Warming up 2.49,2.854 3.198,3.365 0.708,0.51 10 10 minutes or more 0.177,0.885 1.219,1.26 1.042,0.375 10 Vehicle Speed 1.604,2.104 2.021,2.49 0.417,0.385 10 [A] 2.75,1.302 3.167,1.688 0.417,0.385 10 [B] 3.563,2.115 3.979,2.5 0.417,0.385 10 [C] 5.135,1.281 5.552,1.667 0.417,0.385 10 [D] 5.521,1.667 5.938,2.052 0.417,0.385 10 [E] 4.667,0.906 5.688,1.208 1.021,0.302 10 At least 3 times 3.365,0.625 4.458,0.99 1.094,0.365 10 Accelerator Pedal Depressed 3.406,1.427 4.479,1.688 1.073,0.26 10 64 km/h or more 5.802,0.302 7.01,0.74 1.208,0.438 10 Accelerator Pedal Released (Fuel-cut) 6.438,2.115 6.99,2.375 0.552,0.26 10 10 km/h 6.333,2.573 6.885,2.833 0.552,0.26 10 Time 3.667,2.854 5.063,3.177 1.396,0.323 10 10 seconds or more 4.188,3.083 5.583,3.406 1.396,0.323 10 4 seconds or more 4.406,3.51 5.802,3.802 1.396,0.292 10 Refer to figure below 6.083,3.146 6.635,3.406 0.552,0.26 10 [F]

A268801E05
3.375,2.625 2.156,0.708 2.156,0.708 2.281,0.708 false 3.646,2.615 3.948,0.885 3.948,0.885 4.146,0.885 false 0.104,0.031 3.042,0.229 2.938,0.198 10 Driving Pattern Detail for [C] through [E]: 0.177,0.583 1.75,0.75 1.573,0.167 10 Reference Engine Speed 2.813,0.177 6.969,0.375 4.156,0.198 10 Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more 0.844,2.198 1.615,2.396 0.771,0.198 10 1400 rpm 1.094,2.385 1.51,2.583 0.417,0.198 10 Idling 2.188,2.958 2.604,3.156 0.417,0.198 10 Idling 3.198,3.094 3.844,3.542 0.646,0.448 10 4 seconds or more 4.417,3.094 5.073,3.521 0.656,0.427 10 4 seconds or more 5.635,3.104 6.281,3.583 0.646,0.479 10 4 seconds or more 2.188,2.51 2.531,2.74 0.344,0.229 10 [C] 2.833,1.146 3.115,1.396 0.281,0.25 10 [D] 3.469,1.563 3.802,1.802 0.333,0.24 10 [E] 2.375,0.615 3.563,0.813 1.188,0.198 10 Delay (3 seconds) 4.198,0.813 5.417,0.979 1.219,0.167 10 Detection Period t1 4.813,2.406 5.167,2.635 0.354,0.229 10 t2 6.042,2.406 6.313,2.646 0.271,0.24 10 t3 6.656,2.646 7.01,2.813 0.354,0.167 10 Time

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

8.

On the GTS, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Primary / Idle Fuel Cut.

9.

Drive the vehicle at a speed between 60 and 120 km/h (37 and 75 mph) for at least 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

With the shift lever in S position [C], accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

HINT:

Fuel-cut is performed when the following conditions are met:

·

Accelerator pedal is fully released.

·

Engine speed is 1400 rpm or higher (fuel injection restart rpm).



12.

Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

13.

Repeat steps [C] through [E] above at least 3 times in one driving cycle.

14.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

17.

Input the DTC: P2195 or P2196.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P2195 or P2196 is output A
DTC P2195 or P2196 and P0136, P0137 or P0138 are output
DTC P2195 or P2196 and other DTCs are output B


HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.



A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?


Result:
Proceed to
YES
NO



YES

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)

NO

4.READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment.


Result:
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195 or P2196 is output) B



A

DTC CAUSED BY RUNNING OUT OF FUEL

B

4.READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)
4.READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Current.

Powertrain > Engine and ECT > Monitor
50010 234

g.

Check that the status of O2 Sensor is Complete. If the status is still Incomplete, drive the vehicle according to the driving pattern again.


h.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details / RANGE B1S1.

Powertrain > Engine and ECT > Monitor
50010 234

i.

Check the test value of the air fuel ratio sensor output current during fuel-cut.


Result:
Result Proceed to
Within normal range (0.7 mA or higher, and lower than 2.2 mA) A
Outside normal range (lower than 0.7 mA, or 2.2 mA or higher) B



A

5.READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)

B

15.REPLACE AIR FUEL RATIO SENSOR
5.READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Ptrl AF Control / AFS Voltage B1S1 and O2S B1S2.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
O2S B1S2
50004 234 2 35,44

f.

Perform the Control the Injection Volume operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1
(Air fuel ratio)
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
O2S B1S2
(Heated oxygen)
-12.5% Lean Below 0.4 V


Result:
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction
Lean/Rich Lean/Rich Normal


Lean: During the Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During the Control the Injection Volume Active Test, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the heated oxygen sensor alternates correctly.

HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DATA LIST / ACTIVE TEST



A

6.CHECK INTAKE SYSTEM

B

15.REPLACE AIR FUEL RATIO SENSOR
6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in the intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

8.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

9.INSPECT FUEL INJECTOR ASSEMBLY

NG

14.CHECK FUEL LINE
9.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

10.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment result.


Result:
Result Proceed to
ABNORMAL (DTC P2195 or P2196 is output) A
NORMAL (DTC is not output) B



A

12.REPLACE ECM

B

END

12.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment result.

Result:
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





Result:
Proceed to
NEXT



NEXT

END

14.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL LINE

15.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment result.


Result:
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195 or P2196 is output) B



A

END

B