Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0051076 SFI SYSTEM(w/o Canister Pump Module) J

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A240424E23
4.375,1.073 6.198,1.25 1.823,0.177 10 5 V Constant Voltage Circuit 5.354,1.927 6.365,2.344 1.01,0.417 10 Microprocessor 0.917,1.49 2.667,1.719 1.75,0.229 10 from EFI-MAIN NO. 1 Relay 0.99,1.135 2.667,1.302 1.677,0.167 10 from EFI-MAIN NO. 1 Fuse 3.75,1 4.24,1.219 0.49,0.219 10 BATT 0.313,1.948 2.635,2.458 2.323,0.51 10 Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.302,2.969 2.552,3.396 2.25,0.427 10 Engine Coolant Temperature Sensor, Intake Air Temperature, etc. 4.073,2.823 4.333,3.031 0.26,0.208 10 R 3.698,1.354 4.625,1.552 0.927,0.198 10 +B, +B2 3.708,2.271 4,2.5 0.292,0.229 10 VC 4.885,0.354 5.333,0.583 0.448,0.229 10 ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A299792
0.25,1 0.667,1.167 0.417,0.167 10 false B39 0.25,1.167 1.917,1.583 1.667,0.417 10 false Camshaft Position Sensor (for Intake Camshaft) 0.25,2.625 0.667,2.792 0.417,0.167 10 false B41 0.25,2.792 1.917,3.208 1.667,0.417 10 false Camshaft Position Sensor (for Exhaust Camshaft) 0.25,4.25 0.667,4.417 0.417,0.167 10 false X2 0.25,4.417 2.333,4.833 2.083,0.417 10 false Intake Air Control Valve Actuator (for Tumble Control Valve) 2.583,1 2.833,1.167 0.25,0.167 10 false VC 2.417,1.417 2.833,1.583 0.417,0.167 10 false VV1+ 2.417,1.833 2.833,2 0.417,0.167 10 false VV1- 2.5,2.625 2.833,2.792 0.333,0.167 10 false VC2 2.417,3.031 2.833,3.198 0.417,0.167 10 false VVE+ 2.417,3.458 2.833,3.625 0.417,0.167 10 false VVE- 2.5,4.25 2.833,4.417 0.333,0.167 10 false VDD 2.5,4.667 2.833,4.833 0.333,0.167 10 false OUT 2.5,5.083 2.833,5.25 0.333,0.167 10 false GND 2.917,0.833 3.083,1 0.167,0.167 10 false 3 2.917,1.25 3.083,1.417 0.167,0.167 10 false 1 2.917,1.667 3.083,1.833 0.167,0.167 10 false 2 2.917,2.479 3.083,2.646 0.167,0.167 10 false 3 2.917,2.896 3.083,3.063 0.167,0.167 10 false 1 2.917,3.313 3.083,3.479 0.167,0.167 10 false 2 2.917,4.083 3.083,4.25 0.167,0.167 10 false 3 2.917,4.5 3.083,4.667 0.167,0.167 10 false 1 2.917,4.917 3.083,5.083 0.167,0.167 10 false 2 6.083,6 6.417,6.167 0.333,0.167 10 false ECM 5.333,1 5.625,1.167 0.292,0.167 10 false B77 5.333,1.417 5.625,1.583 0.292,0.167 10 false B77 5.333,1.833 5.625,2 0.292,0.167 10 false B77 5.333,2.625 5.625,2.792 0.292,0.167 10 false B77 5.333,3.031 5.625,3.198 0.292,0.167 10 false B77 5.333,3.458 5.625,3.625 0.292,0.167 10 false B77 5.333,4.25 5.625,4.417 0.292,0.167 10 false B77 5.333,4.656 5.625,4.823 0.292,0.167 10 false B77 5.333,5.073 5.625,5.24 0.292,0.167 10 false B77 5.333,0.833 5.667,1 0.333,0.167 10 false 113 5.667,0.833 6.083,1 0.417,0.167 10 false VCV1 5.667,1.417 6.083,1.583 0.417,0.167 10 false VV1+ 5.667,1.667 6.083,1.833 0.417,0.167 10 false VV1- 5.667,2.458 6.083,2.625 0.417,0.167 10 false VCE1 5.667,3.021 6.083,3.188 0.417,0.167 10 false EV1+ 5.667,3.281 6.083,3.448 0.417,0.167 10 false EV1- 5.667,4.083 6.083,4.25 0.417,0.167 10 false VCIA 5.667,4.656 6.083,4.823 0.417,0.167 10 false IAC1 5.667,4.917 6.083,5.083 0.417,0.167 10 false EIA1 5.375,1.25 5.708,1.417 0.333,0.167 10 false 82 5.333,1.667 5.667,1.833 0.333,0.167 10 false 114 5.333,2.458 5.667,2.625 0.333,0.167 10 false 111 5.375,2.865 5.708,3.031 0.333,0.167 10 false 81 5.333,3.281 5.667,3.448 0.333,0.167 10 false 112 5.333,4.083 5.667,4.25 0.333,0.167 10 false 130 5.333,4.5 5.667,4.667 0.333,0.167 10 false 131 5.333,4.917 5.667,5.083 0.333,0.167 10 false 129

A255263E10
6.125,5.146 6.469,5.302 0.344,0.156 10 ECM 5.354,0.865 5.781,1.135 0.427,0.271 10 125 5.667,0.927 6.188,1.229 0.521,0.302 10 VCTA 5.333,1.021 5.76,1.365 0.427,0.344 10 B77 5.354,1.229 5.75,1.51 0.396,0.281 10 127 5.333,1.385 5.698,1.646 0.365,0.26 10 B77 5.354,1.604 5.615,1.76 0.26,0.156 10 128 5.333,1.75 5.688,1.938 0.354,0.188 10 B77 5.333,2.115 5.76,2.313 0.427,0.198 10 B77 5.354,1.969 5.604,2.125 0.25,0.156 10 126 5.667,1.385 6.052,1.531 0.385,0.146 10 VTA1 5.667,1.75 6.052,1.896 0.385,0.146 10 VTA2 5.667,2.031 5.979,2.177 0.313,0.146 10 ETA 5.385,2.406 5.688,2.688 0.302,0.281 10 53 5.333,2.542 5.667,2.76 0.333,0.219 10 A62 5.333,2.906 5.906,3.188 0.573,0.281 10 A62 5.333,3.271 5.729,3.479 0.396,0.208 10 A62 5.333,3.667 5.802,3.906 0.469,0.24 10 A62 5.333,4.031 5.979,4.313 0.646,0.281 10 A62 5.323,4.396 5.844,4.74 0.521,0.344 10 A62 5.385,2.771 5.833,3 0.448,0.229 10 56 5.385,3.135 5.719,3.323 0.333,0.188 10 51 5.385,3.531 5.771,3.781 0.385,0.25 10 54 5.385,3.875 5.74,4.115 0.354,0.24 10 52 5.385,4.26 5.688,4.542 0.302,0.281 10 55 5.667,2.458 6.073,2.615 0.406,0.156 10 VCPA 5.667,3.281 5.979,3.438 0.313,0.156 10 VPA 5.667,3.958 5.979,4.115 0.313,0.156 10 EPA 5.667,3.667 6.042,3.823 0.375,0.156 10 VPA2 5.667,4.323 6.115,4.563 0.448,0.24 10 EPA2 5.667,2.833 6.073,2.99 0.406,0.156 10 VCP2 0.25,1.167 0.948,1.448 0.698,0.281 10 B3 0.25,1.344 1.771,1.906 1.521,0.563 10 Throttle with Motor Body Assembly 2.594,1.021 3.115,1.26 0.521,0.24 10 VC 2.521,1.375 2.833,1.531 0.313,0.156 10 VTA 2.448,1.74 2.958,2.052 0.51,0.313 10 VTA2 2.625,2.104 2.844,2.271 0.219,0.167 10 E2 2.938,0.927 3.052,1.083 0.115,0.156 10 5 2.938,1.292 3.052,1.448 0.115,0.156 10 6 2.938,1.656 3.052,1.813 0.115,0.156 10 4 2.938,2.021 3.052,2.177 0.115,0.156 10 3 0.25,2.688 0.656,2.844 0.406,0.156 10 A6 0.25,2.865 1.385,3.479 1.135,0.615 10 Accelerator Pedal Sensor Assembly 2.438,2.552 3,2.792 0.563,0.24 10 VCPA 2.438,2.927 2.854,3.073 0.417,0.146 10 VCP2 2.521,3.292 2.896,3.458 0.375,0.167 10 VPA 2.448,3.667 2.969,3.896 0.521,0.229 10 VPA2 2.531,4.031 3,4.271 0.469,0.24 10 EPA 2.448,4.375 3.083,4.646 0.635,0.271 10 EPA2 2.938,2.458 3.052,2.615 0.115,0.156 10 4 2.938,2.833 3.052,2.99 0.115,0.156 10 1 2.938,3.188 3.052,3.344 0.115,0.156 10 6 2.938,3.594 3.052,3.75 0.115,0.156 10 3 2.938,3.948 3.052,4.104 0.115,0.156 10 5 2.938,4.313 3.052,4.469 0.115,0.156 10 2

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK GTS
2.CHECK GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle with motor body assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B


HINT:

Perform "Inspection After Repair" after replacing the throttle with motor body assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION



A

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK MIL (INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE))

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK MIL (INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE))
a.

Disconnect the intake air control valve actuator (for tumble control valve) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

6.CHECK MIL (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT)

B

REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

6.CHECK MIL (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT)
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

7.CHECK MIL (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

7.CHECK MIL (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

8.CHECK HARNESS AND CONNECTOR

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

8.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle with motor body assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the intake air control valve actuator (for tumble control valve) connector.


d.

Disconnect the camshaft position sensor (for intake camshaft) connector.


e.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


f.

Disconnect the ECM connectors.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B77-125 (VCTA) - Body ground Always 10 kΩ or higher
A62-53 (VCPA) - Body ground Always 10 kΩ or higher
A62-56 (VCP2) - Body ground Always 10 kΩ or higher
B77-130 (VCIA) - Body ground Always 10 kΩ or higher
B77-111 (VCE1) - Body ground Always 10 kΩ or higher
B77-113 (VCV1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR