These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1507 | Open in Turn Signal Circuit | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
Open in turn signal light circuit. |
·
Bulb ·
Harness or connector ·
Side turn signal light assembly ·
Outer rear view mirror sub-assembly ·
Rear combination light socket and wire sub-assembly ·
Combination meter assembly |
| B1508 | Short in Turn Signal / Hazard Flasher Circuit | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
Short in turn signal light circuit or hazard warning light circuit. |
·
Bulb ·
Harness or connector ·
Side turn signal light assembly ·
Outer rear view mirror sub-assembly ·
Rear combination light socket and wire sub-assembly ·
Combination meter assembly |
Inspect the bulbs for this system before performing the following procedure.
When replacing the combination meter assembly, make sure to replace it with a new one.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1507 or B1508 output does not occur |
| DTC B1507 or B1508 is output |
DTC B1507 or B1508 output does not occur
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC B1507 or B1508 is output
Check the malfunctioning turn signal light.
| Proceed to |
|---|
| No right turn signal lights turn on |
| No left turn signal lights turn on |
| One of the right turn signal lights does not turn on |
| One of the left turn signal lights does not turn on |
No right turn signal lights turn on
No left turn signal lights turn on
One of the right turn signal lights does not turn on
One of the left turn signal lights does not turn on
*1: w/o Panic Switch
*2: w/ Panic Switch
*3: w/ Side Turn Signal Light
Disconnect the G17 combination meter assembly connector.
Disconnect the M19 rear combination light socket wire sub-assembly RH connector.
Disconnect the A42*1 or A41*2 front turn signal light RH connector.
Disconnect the I8 outer rear view mirror sub-assembly RH connector.*3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-7 (LR) - M19-3 (TRN) | Always | Below 1 Ω |
| G17-7 (LR) or M19-3 (TRN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: w/o Panic Switch
*2: w/ Panic Switch
*3: w/ Side Turn Signal Light
Disconnect the G17 combination meter assembly connector.
Disconnect the N13 rear combination light socket wire sub-assembly LH connector.
Disconnect the A16*1 or A17*2 front turn signal light LH connector.
Disconnect the J8 outer rear view mirror sub-assembly LH connector.*3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-13 (LL) - N13-3 (TRN) | Always | Below 1 Ω |
| G17-13 (LL) or N13-3 (TRN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the malfunctioning turn signal light.
| Result | Proceed to |
|---|---|
| Front turn signal light does not illuminate | A |
| Side turn signal light does not illuminate (w/ Side Turn Signal Light) | B |
| Rear turn signal light do not illuminate | C |
A
B
C
*1: w/o Panic Switch
*2: w/ Panic Switch
*3: w/ Side Turn Signal Light
Disconnect the G17 combination meter assembly connector.
Disconnect the A42*1 or A41*2 front turn signal light RH connector.
Disconnect the I8 outer rear view mirror sub-assembly RH connector.*3
Disconnect the M19 rear combination light socket wire sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-7 (LR) - A42-2 (B) | Always | Below 1 Ω |
| A42-1 (E) - Body ground | ||
| G17-7 (LR) or A42-2 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-7 (LR) - A41-1 (B) | Always | Below 1 Ω |
| A41-2 (E) - Body ground | ||
| G17-7 (LR) or A41-1 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
*1: w/o Panic Switch
*2: w/ Panic Switch
Disconnect the G17 combination meter assembly connector.
Disconnect the I8 outer rear view mirror sub-assembly RH connector.
Disconnect the A42*1 or A41*2 front turn signal light RH connector.
Disconnect the M19 rear combination light socket wire sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-7 (LR) - I8-10 (B) | Always | Below 1 Ω |
| I8-11 (E) - Body ground | ||
| G17-7 (LR) or I8-10 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer rear view mirror assembly RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Connect the positive (+) lead from the battery to terminal 10 and the negative (-) lead to terminal 11, and check that the light comes on.
| Proceed to |
|---|
| Light comes on |
| Light not comes on |
Light comes on
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Light not comes on
*1: w/o Panic Switch
*2: w/ Panic Switch
*3: w/ Side Turn Signal Light
Disconnect the G17 combination meter assembly connector.
Disconnect the M19 rear combination light socket wire sub-assembly RH connector.
Disconnect the A42*1 or A41*2 front turn signal light RH connector.
Disconnect the I8 outer rear view mirror sub-assembly RH connector.*3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-7 (LR) - M19-3 (TRN) | Always | Below 1 Ω |
| M19-4 (E) - Body ground | ||
| G17-7 (LR) or M19-3 (TRN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the side turn signal light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Inspect the side turn signal light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the malfunctioning turn signal light.
| Result | Proceed to |
|---|---|
| Front turn signal lights does not illuminates | A |
| Side turn signal lights does not illuminates (w/ Side Turn Signal Light) | B |
| Rear turn signal lights does not illuminates | C |
A
B
C
*1: w/o Panic Switch
*2: w/ Panic Switch
*3: w/ Side Turn Signal Light
Disconnect the G17 combination meter assembly connector.
Disconnect the A16*1 or A17*2 front turn signal light LH connector.
Disconnect the J8 outer rear view mirror sub-assembly LH connector.*3
Disconnect the N13 rear combination light socket wire sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-13 (LL) - A16-2 (B) | Always | Below 1 Ω |
| A16-1 (E) - Body ground | ||
| G17-13 (LL) or A16-2 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-13 (LL) - A17-1 (B) | Always | Below 1 Ω |
| A17-2 (E) - Body ground | ||
| G17-13 (LL) or A17-1 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
*1: w/o Panic Switch
*2: w/ Panic Switch
Disconnect the G17 combination meter assembly connector.
Disconnect the J8 outer rear view mirror sub-assembly LH connector.
Disconnect the A16*1 or A17*2 front turn signal light LH connector.
Disconnect the N13 rear combination light socket wire sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-13 (LL) - J8-10 (B) | Always | Below 1 Ω |
| J8-11 (E) - Body ground | ||
| G17-13 (LL) or J8-10 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer rear view mirror assembly LH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Connect the positive (+) lead from the battery to terminal 10 and the negative (-) lead to terminal 11, and check that the light comes on.
| Proceed to |
|---|
| Light comes on |
| Light not comes on |
Light comes on
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Light not comes on
*1: w/o Panic Switch
*2: w/ Panic Switch
*3: w/ Side Turn Signal Light
Disconnect the G17 combination meter assembly connector.
Disconnect the N13 rear combination light socket wire sub-assembly LH connector.
Disconnect the A16*1 or A17*2 front turn signal light LH connector.
Disconnect the J8 outer rear view mirror sub-assembly LH connector.*3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-13 (LL) - N13-3 (TRN) | Always | Below 1 Ω |
| N13-4 (E) - Body ground | ||
| G17-13 (LL) or N13-3 (TRN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the side turn signal light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Inspect the side turn signal light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG