1.REMOVE FRONT WHEEL
51441
2.REMOVE NO. 1 ENGINE UNDER COVER
for 2AD-FTV, 2AD-FHV: (Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
for 2AR-FE: (Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
for 3ZR-FE: (Click hereEngine / Hybrid System>3ZR-FE COOLING>COOLANT>REPLACEMENT)
for 3ZR-FAE: (Click hereEngine / Hybrid System>3ZR-FAE COOLING>COOLANT>REPLACEMENT)
51444C
3.REMOVE REAR ENGINE UNDER COVER LH
for 2AD-FTV, 2AD-FHV: (Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
for 2AR-FE: (Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
for 3ZR-FE: (Click hereEngine / Hybrid System>3ZR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
for 3ZR-FAE: (Click hereEngine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
51443
4.REMOVE REAR ENGINE UNDER COVER RH
for 2AD-FTV, 2AD-FHV: (Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>DRIVE BELT>REMOVAL)
for 2AR-FE: (Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
for 3ZR-FE: (Click hereEngine / Hybrid System>3ZR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
for 3ZR-FAE: (Click hereEngine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL)
5.DRAIN AUTOMATIC TRANSAXLE FLUID
for U660F: (Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>REMOVAL)
for U760F: (Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>REMOVAL)
6.DRAIN MANUAL TRANSAXLE OIL
for EA64F: (Click hereDrivetrain>EA64F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE OIL>REPLACEMENT)
for EB61F: (Click hereDrivetrain>EB61F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE OIL>REPLACEMENT)
for EB63F: (Click hereDrivetrain>EB63F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE OIL>REPLACEMENT)
7.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID
8.DRAIN TRANSFER OIL
43502H
9.REMOVE FRONT AXLE SHAFT NUT LH
43501H
10.REMOVE FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
11.DISCONNECT FRONT SPEED SENSOR LH
12.DISCONNECT FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
48810
13.REMOVE FRONT STABILIZER LINK ASSEMBLY LH
48820B
14.REMOVE FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
48069
15.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
16.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
17.DISCONNECT STEERING KNUCKLE WITH AXLE HUB LH
Remove the bolt and detach the 2 guides.
| *a | Matchmark |
Put matchmarks on the front drive shaft assembly and front axle hub sub-assembly.
Do not use a punch to make the matchmarks.
Using a plastic-faced hammer, disconnect the front drive shaft assembly from the steering knuckle with axle hub.
Be careful not to damage the boot and drive shaft dust cover.
Do not excessively push out the drive shaft from the front axle hub.
18.DISCONNECT STEERING KNUCKLE WITH AXLE HUB RH
Use the same procedure described for the LH side.
43420
19.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
Using SST, remove the front drive shaft assembly LH.
Be careful not to damage the transaxle oil seal, inboard joint boot and drive shaft dust cover.
Be careful not to drop the front drive shaft assembly LH.
43410
20.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
Disconnect the drive shaft bearing bracket hole snap ring from the drive shaft bearing bracket.
Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.
Be careful not to damage the transaxle oil seal, inboard joint boot and drive shaft dust cover.
Be careful not to drop the front drive shaft assembly RH.
Remove the drive shaft bearing bracket hole snap ring from the front drive shaft assembly RH.
43420G
21.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH
Using a screwdriver, remove the front drive shaft hole snap ring LH.