Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet and MRE (Magneto Resistance Element).

The G signal plate (camshaft timing gear or sprocket) has 3 teeth on its outer circumference and is installed on the camshaft. When the camshaft rotates, the protrusion on the signal plate and the air gap on the MRE change, causing fluctuations in the magnetic field that generate a voltage in the MRE.

The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G signal, and detects the crankshaft angle based on the NE signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) Phase deviation in crankshaft and camshaft position sensor signals with an engine speed of 650 to 3000 rpm occurs a certain number of times (1 trip detection logic).
·

Camshaft position sensor circuit

·

Camshaft position sensor

·

Crankshaft position sensor

·

Camshaft timing gear or sprocket

·

ECM


Does not come on DTC Stored
P0340 Camshaft Position Sensor Circuit Malfunction STA on:
No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more (2 trip detection logic).
STA off:
Camshaft position sensor signal is not input with an engine speed of 650 rpm or more (1 trip detection logic).
·

Camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft timing sprocket

·

ECM


Comes on DTC Stored
P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) Output voltage of camshaft position sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

ECM


Comes on DTC Stored
P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) Output voltage of camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

ECM


Comes on DTC Stored

HINT:

If DTC P0016, P0340, P0342 and/or P0343 is stored, the following symptoms may appear:

·

Difficulty starting

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0016 Idle engine for 1 second
P0340
·

Crank engine for 4 seconds (STA on)

·

Idle engine for 1 second (STA off)


P0342 Idle engine for 4 second
P0342

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:
·

After performing the inspection procedure for the camshaft position sensor, if DTC P0016 and/or P0340 is output again, check the following items related to the crankshaft position sensor.

·

Installation condition of the crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

Connection of the crankshaft position sensor connector


·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B27-3 (VC) - B76-78 (VCG) Always Below 1 Ω
B27-1 (G2R) - B76-80 (G2+) Always Below 1 Ω
B27-2 (G-R) - B76-79 (G2-) Always Below 1 Ω
B27-3 (VC) or B76-78 (VCG) - Body ground Always 10 kΩ or higher
B27-1 (G2R) or B76-80 (G2+) - Body ground Always 10 kΩ or higher
B27-2 (G-R) or B76-79 (G2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR)
a.
A186169
0.271,1.5 0.667,1.75 0.396,0.25 2.323,2.906 1.99,2.229 true 0.156,0.156 0.375,0.396 0.219,0.24 10 false *a 0.323,1.542 0.688,1.729 0.365,0.188 10 false B27 2.271,2.927 2.635,3.115 0.365,0.188 10 false VC
*a Front view of wire harness connector
(to Camshaft Position Sensor)


Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B27-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

8.REPLACE ECM
3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
A208464
0.401,1.758 0.649,1.91 0.249,0.152 10 OK 2.664,1.768 2.912,1.92 0.249,0.152 10 NG

Check the camshaft position sensor installation.

OK:

Camshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.CHECK CAMSHAFT TIMING GEAR OR SPROCKET

NG

11.SECURELY REINSTALL CAMSHAFT POSITION SENSOR
4.CHECK CAMSHAFT TIMING GEAR OR SPROCKET
a.

Check the condition of the camshaft timing gear or sprocket.

OK:

Camshaft timing gear or sprocket does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR CIRCUIT)

NG

9.REPLACE CAMSHAFT TIMING GEAR OR SPROCKET
5.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR CIRCUIT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Start the engine and idle it for 4 seconds or more.


g.

Turn the GTS on.


h.

Check the engine condition while wiggling the crankshaft position sensor wire harness for 4 seconds or more when idling.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
Except below A
There are problem such as rough idle or engine stall when wire harness is wiggles, or DTC is output* B


HINT:

*: As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE




A

6.REPLACE CAMSHAFT POSITION SENSOR

B

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE CAMSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and idle it for 4 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0016, P0340, P0342 or P0343 is output A
DTC is not output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE CAMSHAFT TIMING GEAR OR SPROCKET
a.

Replace the camshaft timing gear or sprocket.

Click hereEngine / Hybrid System>1AD-FTV ENGINE MECHANICAL>CAMSHAFT>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and idle it for 4 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END

11.SECURELY REINSTALL CAMSHAFT POSITION SENSOR
a.

Securely reinstall the camshaft position sensor.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>CAMSHAFT POSITION SENSOR>INSTALLATION


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED