Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the common rail injection system is controlled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit When the following condition is met (for 5 seconds during cranking or 0.5 seconds during engine start) (1 trip detection logic):
No crankshaft position sensor signal is sent to the ECM while cranking.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

ECM


Comes on DTC stored
P0339 Crankshaft Position Sensor "A" Circuit Intermittent No crankshaft position sensor signal is input to the ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met (1 trip detection logic):
(a) Engine speed is 1000 rpm or more.
(b) STA signal is off.
(c) 3 seconds or more have elapsed after STA signal is switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P0335 Engine Speed
P0339

HINT:

If DTC P0335 and/or P0339 is stored, the following symptoms may appear:

·

Difficulty starting

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0335 Crank or start engine
P0339 Engine running at 1000 rpm or higher with vehicle stationary

WIRING DIAGRAM

A298511
3.542,4.354 5.229,4.552 1.688,0.198 10 false *: Shielded 0.208,2.25 2.125,2.531 1.917,0.281 10 false Camshaft Position Sensor 0.167,4.469 2.083,4.75 1.917,0.281 10 false Crankshaft Position Sensor 0.198,2.104 2.115,2.385 1.917,0.281 10 false B27 0.167,4.313 2.083,4.594 1.917,0.281 10 false B29 1.021,4.031 1.448,4.26 0.427,0.229 10 false GND 1.083,3.667 1.51,3.896 0.427,0.229 10 false NE- 1.135,2.969 1.563,3.198 0.427,0.229 10 false NE 1.083,1.771 1.51,2 0.427,0.229 10 false G-R 1.052,1.313 1.479,1.542 0.427,0.229 10 false G2R 1.115,0.833 1.542,1.063 0.427,0.229 10 false VC 1.448,0.698 1.875,0.927 0.427,0.229 10 false 3 1.458,1.167 1.885,1.396 0.427,0.229 10 false 1 1.458,1.635 1.885,1.865 0.427,0.229 10 false 2 1.448,2.833 1.875,3.063 0.427,0.229 10 false 1 1.458,3.542 1.885,3.771 0.427,0.229 10 false 2 1.458,3.917 1.885,4.146 0.427,0.229 10 false 3 5.156,0.688 5.583,0.917 0.427,0.229 10 false 78 5.156,1.167 5.583,1.396 0.427,0.229 10 false 80 5.156,1.635 5.583,1.865 0.427,0.229 10 false 79 5.073,2.844 5.5,3.073 0.427,0.229 10 false 103 5.083,3.542 5.51,3.771 0.427,0.229 10 false 102 5.438,0.823 5.865,1.052 0.427,0.229 10 false VCG 5.438,1.292 5.865,1.521 0.427,0.229 10 false G2+ 5.448,1.75 5.875,1.979 0.427,0.229 10 false G2- 5.438,2.969 5.865,3.198 0.427,0.229 10 false NE+ 5.438,3.656 5.865,3.885 0.427,0.229 10 false NE- 5.688,4.469 6.115,4.698 0.427,0.229 10 false B76 6.167,4.469 6.594,4.698 0.427,0.229 10 false ECM 2.688,3.969 2.979,4.177 0.292,0.208 10 false *

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

The Data List item Engine Speed is calculated from the output of the crankshaft position sensor.

·

A DTC is also stored when the ground of a shielded wire is faulty.



PROCEDURE

1.INSPECT CRANKSHAFT POSITION SENSOR

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

10.REPLACE CRANKSHAFT POSITION SENSOR
2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B29-1 (NE) - B76-103 (NE+) Always Below 1 Ω
B29-2 (NE-) - B76-102 (NE-) Always Below 1 Ω
B29-3 (GND) - Body ground Always Below 1 Ω
B29-1 (NE) or B76-103 (NE+) - Body ground Always 10 kΩ or higher
B29-2 (NE-) or B76-102 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
A208464
0.49,1.76 0.76,1.948 0.271,0.188 10 *a 2.667,1.802 2.906,2.031 0.24,0.229 10 *b
*a OK
*b NG


Check the crankshaft position sensor installation.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE

NG

8.SECURELY REINSTALL CRANKSHAFT POSITION SENSOR
4.CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE
a.

Check the teeth of the No. 1 crankshaft position sensor plate.

OK:

The No. 1 crankshaft position sensor plate teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.REPLACE NO.1 CRANKSHAFT POSITION SENSOR PLATE
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE NO.1 CRANKSHAFT POSITION SENSOR PLATE
a.

Replace the No. 1 crankshaft position sensor plate.

Click hereEngine / Hybrid System>1AD-FTV ENGINE MECHANICAL>CYLINDER BLOCK>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and run it at 1000 rpm or higher for 5 seconds or more.


g.

Tune the ignition switch to ON and turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Cades.


i.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END

8.SECURELY REINSTALL CRANKSHAFT POSITION SENSOR
a.

Securely reinstall the crankshaft position sensor.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>INSTALLATION


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED