When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head sub-assembly, it is necessary to replace the injection pipes with new ones.
When replacing the fuel supply pump, common rail, intake manifold or cylinder head sub-assembly, it is necessary to replace the fuel inlet pipe with a new one.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.REMOVE ENGINE ASSEMBLY
4.DISCONNECT ENGINE WIRE
27020
5.REMOVE GENERATOR ASSEMBLY
29300
6.REMOVE VACUUM PUMP ASSEMBLY
16649B
7.REMOVE IDLER PULLEY COVER PLATE
16603
8.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
16604
9.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY
16288
10.REMOVE NO. 4 WATER BY-PASS PIPE
12315A
11.REMOVE ENGINE MOUNTING BRACKET
16620
12.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
26100
13.REMOVE DIESEL THROTTLE BODY ASSEMBLY
16295
14.REMOVE NO. 7 WATER BY-PASS HOSE
16296
15.DISCONNECT NO. 8 WATER BY-PASS HOSE
25625
16.REMOVE EGR VALVE BRACKET
25602
17.REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY
25800
18.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
11452
19.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
23804C
20.REMOVE FUEL INLET PIPE SUB-ASSEMBLY
23701
21.REMOVE INJECTION PIPE SUB-ASSEMBLY
23282D
22.REMOVE NO. 4 FUEL HOSE
23810A
23.REMOVE COMMON RAIL ASSEMBLY
17853B
24.REMOVE INTAKE MANIFOLD INSULATOR
89421C
25.REMOVE DIESEL TURBO PRESSURE SENSOR
23265
26.REMOVE NO. 1 GAS FILTER
17696
27.REMOVE GAS FILTER BRACKET
12631A
28.REMOVE ENGINE COVER BRACKET
17112
29.REMOVE NO. 2 INTAKE MANIFOLD
17111
30.REMOVE INTAKE MANIFOLD
16261
31.REMOVE WATER BY-PASS HOSE
15710
32.REMOVE OIL COOLER ASSEMBLY
16283
33.REMOVE NO. 6 WATER BY-PASS HOSE
16296
34.REMOVE NO. 8 WATER BY-PASS HOSE
16279
35.REMOVE NO. 3 WATER BY-PASS PIPE
15481
36.REMOVE NO. 1 TURBO OIL PIPE
15781
37.REMOVE NO. 1 OIL COOLER BRACKET
12581A
38.REMOVE NO. 1 CYLINDER BLOCK INSULATOR
16278
39.REMOVE NO. 2 WATER BY-PASS PIPE
16281
40.REMOVE NO. 4 WATER BY-PASS HOSE
16323
41.REMOVE WATER INLET HOUSING
23292A
42.REMOVE FUEL HOSE PROTECTOR
23901E
43.REMOVE FUEL TUBE SUB-ASSEMBLY
23274D
44.REMOVE NO. 3 FUEL HOSE
23762
45.REMOVE NO. 2 NOZZLE LEAKAGE PIPE
23761A
46.REMOVE NO. 1 NOZZLE LEAKAGE PIPE
23695
47.REMOVE NO. 1 NOZZLE HOLDER CLAMP
23670
48.REMOVE INJECTOR ASSEMBLY
25860
49.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY
25760A
50.REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY
51.REMOVE NO. 1 WIRING HARNESS CLAMP BRACKET
12261
52.REMOVE PCV HOSE
12108
53.REMOVE OIL FILLER CAP SUB-ASSEMBLY
11201
54.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
12102A
55.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
04152
56.REMOVE OIL FILTER ELEMENT
15350A
57.REMOVE OIL PRESSURE SWITCHING VALVE ASSEMBLY
15677
58.REMOVE OIL FILTER BRACKET
15104
59.REMOVE OIL STRAINER SUB-ASSEMBLY
11301K
60.REMOVE CAMSHAFT POSITION SENSOR
11401G
61.DISCONNECT CRANKSHAFT POSITION SENSOR WIRE HARNESS
16100
62.REMOVE ENGINE WATER PUMP ASSEMBLY
13471
63.REMOVE CRANKSHAFT PULLEY
11302
64.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
22100
65.REMOVE FUEL SUPPLY PUMP ASSEMBLY
13540
66.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
13559
67.REMOVE CHAIN TENSIONER SLIPPER
13561
68.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13519
69.REMOVE OIL PUMP DRIVE GEAR
13523
70.REMOVE CAMSHAFT TIMING SPROCKET
13521
71.REMOVE CRANKSHAFT TIMING SPROCKET
13511
72.REMOVE CAMSHAFT
Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.
| *1 | Oil Pipe Seat |
| *2 | No. 4 Camshaft Bearing Cap |
Remove the 2 oil pipe seats.
Uniformly loosen the 20 bolts in several steps in the sequence shown in the illustration and remove the bolts.
Remove the 8 No. 3 camshaft bearing caps and No. 1 camshaft bearing cap.
Do not remove the No. 4 camshaft bearing cap.
Remove the camshaft and No. 2 camshaft.
Remove the No. 2 camshaft bearing cap.
13801
73.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 16 No. 1 valve rocker arm sub-assemblies.
13750
74.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.
Arrange the removed parts in the correct order.