Vehicles which are equipped with a manual transmission detect the vehicle speed using the speed sensor. The speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transaxle output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter assembly. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0500 | Vehicle Speed Sensor "A" | Either of the following conditions is met (2 trip detection logic):
·
Conditions (a), (b), (c) and (d) are met for 8 seconds or more: (a) Engine coolant temperature is higher than 70°C (158°F). (b) engine speed is 1500 to 4000 rpm (c) Injection volume is 20 mm3/st or higher. (d) No speed signal is input to the ECM. ·
Conditions (a) and (b) are met for 4.5 seconds or more: (a) During the fuel cut operation. (b) No speed signal is input to the ECM. |
·
Open or short in speedometer circuit ·
Speedometer assembly ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0500 | Vehicle Speed |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0500 | Drive the vehicle at 10 km/h (6.3 mph) or more |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.
The vehicle speed sensor is operating normally if the speedometer reading is normal.
The vehicle speed sensor is operating normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.
| Tester Display |
|---|
| Vehicle Speed |
Drive the vehicle.
Read the value displayed on the GTS.
Vehicle speeds displayed on GTS and speedometer display are equal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
| *a | Component with harness connected
(Combination Meter Assembly) |
Move the shift lever to neutral.
Jack up the vehicle.
Check the voltage between the terminal of the combination meter assembly and the body ground while a wheel is turned slowly.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | Voltage generated intermittently |
The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the combination meter assembly.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the combination meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - A61-14 (SPD) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the speedometer circuit.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit
Inspect the skid control ECU (brake actuator assembly) and speed sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off.
Start the engine.
Drive the vehicle at 10 km/h (6.3 mph) or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the pending DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT