Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P064C  Glow Plug Control Module  P066B  Cylinder 1 Glow Plug Control Circuit High  P066D  Cylinder 2 Glow Plug Control Circuit High  P066F  Cylinder 3 Glow Plug Control Circuit High  P0671  Cylinder 1 Glow Plug Circuit/Open  P0672  Cylinder 2 Glow Plug Circuit/Open  P0673  Cylinder 3 Glow Plug Circuit/Open  P0674  Cylinder 4 Glow Plug Circuit/Open  P067B  Cylinder 4 Glow Plug Control Circuit High  P166F  Glow Plug Control Module Circuit Short  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P064C Glow Plug Control Module The MOS inside the glow plug controller is detected as being stuck on 3 times while the glow plug assemblies are on (2 trip detection logic). Glow plug controller Comes on DTC stored
P066B Cylinder 1 Glow Plug Control Circuit High A short circuit in the No. 1 glow plug circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug assembly

·

Short in No. 1 glow plug assembly circuit


Comes on DTC stored
P066D Cylinder 2 Glow Plug Control Circuit High A short circuit in the No. 2 glow plug circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug assembly

·

Short in No. 2 glow plug assembly circuit


Comes on DTC stored
P066F Cylinder 3 Glow Plug Control Circuit High A short circuit in the No. 3 glow plug circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug assembly

·

Short in No. 3 glow plug assembly circuit


Comes on DTC stored
P0671 Cylinder 1 Glow Plug Circuit/Open An open circuit in the No. 1 glow plug circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug assembly

·

Open in No. 1 glow plug assembly circuit

·

Glow plug relay assembly


Comes on DTC stored
P0672 Cylinder 2 Glow Plug Circuit/Open An open circuit in the No. 2 glow plug circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug assembly

·

Open in No. 2 glow plug assembly circuit

·

Glow plug relay assembly


Comes on DTC stored
P0673 Cylinder 3 Glow Plug Circuit/Open An open circuit in the No. 3 glow plug circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug assembly

·

Open in No. 3 glow plug assembly circuit

·

Glow plug relay assembly


Comes on DTC stored
P0674 Cylinder 4 Glow Plug Circuit/Open An open circuit in the No. 4 glow plug circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug assembly

·

Open in No. 4 glow plug assembly circuit

·

Glow plug relay assembly


Comes on DTC stored
P067B Cylinder 4 Glow Plug Control Circuit High A short circuit in the No. 4 glow plug circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug assembly

·

Short in No. 4 glow plug assembly circuit


Comes on DTC stored
P166F Glow Plug Control Module Circuit Short A short circuit in a wire harness between the glow plugs is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

Open or short in glow plug assembly circuit


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P064C Enter check mode
P066B
P066D
P066F
P0671
P0672
P0673
P0674
P067B
P166F

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0671, P0672, P0673 and/or P0674 is output A
DTC P066B, P066D, P066F and/or P067B is output B
DTC P064C and/or P166F is output C




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF GLOW PLUG CONTROLLER)

B

14.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 GLOW PLUG CONNECTOR)

C

19.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 GLOW PLUG CONNECTOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF GLOW PLUG CONTROLLER)
a.
A241159
0.542,0.969 0.958,1.219 0.417,0.25 1.781,1.26 2.125,1.771 true 0.135,0.167 0.323,0.344 0.188,0.177 10 false *a 2.156,1.76 2.542,1.938 0.385,0.177 10 false BATT 0.646,1.01 1.292,1.292 0.646,0.281 10 false W4
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect the glow plug controller connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W4-1(BATT) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 GLOW PLUG CONNECTOR)

NG

8.INSPECT GLOW PLUG RELAY ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 GLOW PLUG CONNECTOR)
a.
A275104
0.719,2.667 1.104,2.917 0.385,0.25 0.75,3.844 1.135,4.094 0.385,0.25 0.875,1.281 1.135,0.969 true 1.458,1.604 1.719,1.292 true 2.042,1.906 2.302,1.594 true 2.625,2.229 2.885,1.917 true 1.333,3.198 1.594,2.885 true 2.083,3.188 1.854,2.875 true 1.365,4.375 1.625,4.063 true 2.125,4.375 1.896,4.063 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *1 0.49,2.115 0.802,2.271 0.313,0.156 10 false *a 0.792,1.271 1.104,1.427 0.313,0.156 10 false 1 1.385,1.594 1.698,1.75 0.313,0.156 10 false 2 1.958,1.885 2.271,2.042 0.313,0.156 10 false 3 2.552,2.198 2.865,2.354 0.313,0.156 10 false 4 0.802,2.719 1.198,2.906 0.396,0.188 10 false W2 0.823,3.885 1.208,4.063 0.385,0.177 10 false W3 1.188,3.219 1.583,3.406 0.396,0.188 10 false GL1 2,3.208 2.396,3.396 0.396,0.188 10 false GL2 1.188,4.385 1.583,4.573 0.396,0.188 10 false GL3 2.052,4.385 2.448,4.573 0.396,0.188 10 false GL4
*1 No. 1 Glow Plug Connector
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect connectors of the glow plug controller.


b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W2-1 (GL1) - 1 (No. 1 glow plug connector terminal) Always Below 1 Ω
W2-2 (GL2) - 2 (No. 1 glow plug connector terminal) Always Below 1 Ω
W3-1 (GL3) - 3 (No. 1 glow plug connector terminal) Always Below 1 Ω
W3-2 (GL4) - 4 (No. 1 glow plug connector terminal) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT GLOW PLUG ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.INSPECT GLOW PLUG ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off.


e.

Exchange the glow plug assemblies of the malfunctioning cylinders (the cylinders indicated by output DTCs) with the glow plugs of normally functioning cylinders.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
Same DTCs (that have been erased) A
Other DTCs B


HINT:

Check for DTCs in check mode.




A

20.REPLACE GLOW PLUG CONTROLLER

B

5.REPLACE GLOW PLUG ASSEMBLY
5.REPLACE GLOW PLUG ASSEMBLY
a.

Replace the glow plug assembly.

Click hereEngine / Hybrid System>1AD-FTV STARTING>GLOW PLUG>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61
HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END

8.INSPECT GLOW PLUG RELAY ASSEMBLY
a.

Inspect the glow plug relay assembly.

Click hereEngine / Hybrid System>1AD-FTV STARTING>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR

NG

13.REPLACE GLOW PLUG RELAY ASSEMBLY
9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Remove the glow plug relay assembly.


d.

Disconnect connectors of the glow plug controller.


e.

Disconnect the ECM connectors.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B38-4 - Battery positive terminal Always Below 1 Ω
B38-1 - Body ground Always Below 1 Ω
B38-3 - W4-1 (BATT) Always Below 1 Ω
B38-2 - B76-58 (GREL) Always Below 1 Ω
B38-4 or Battery positive terminal - Body ground Always 10 kΩ or higher
B38-3 or W4-1 (BATT) - Body ground Always 10 kΩ or higher
B38-2 or B76-58 (GREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61
HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END

13.REPLACE GLOW PLUG RELAY ASSEMBLY
a.

Replace the glow plug relay assembly.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 GLOW PLUG CONNECTOR)
a.
A275104
0.719,2.667 1.104,2.917 0.385,0.25 0.75,3.844 1.135,4.094 0.385,0.25 0.875,1.281 1.135,0.969 true 1.458,1.604 1.719,1.292 true 2.042,1.906 2.302,1.594 true 2.625,2.229 2.885,1.917 true 1.333,3.198 1.594,2.885 true 2.083,3.188 1.854,2.875 true 1.365,4.375 1.625,4.063 true 2.125,4.375 1.896,4.063 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *1 0.49,2.115 0.802,2.271 0.313,0.156 10 false *a 0.792,1.271 1.104,1.427 0.313,0.156 10 false 1 1.385,1.594 1.698,1.75 0.313,0.156 10 false 2 1.958,1.885 2.271,2.042 0.313,0.156 10 false 3 2.552,2.198 2.865,2.354 0.313,0.156 10 false 4 0.802,2.719 1.198,2.906 0.396,0.188 10 false W2 0.823,3.885 1.208,4.063 0.385,0.177 10 false W3 1.188,3.219 1.583,3.406 0.396,0.188 10 false GL1 2,3.208 2.396,3.396 0.396,0.188 10 false GL2 1.188,4.385 1.583,4.573 0.396,0.188 10 false GL3 2.052,4.385 2.448,4.573 0.396,0.188 10 false GL4
*1 No. 1 Glow Plug Connector
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect connectors of the glow plug controller.


b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W2-1 (GL1) or 1 (No. 1 glow plug connector terminal) - Body ground Always 10 kΩ or higher
W2-2 (GL2) or 2 (No. 1 glow plug connector terminal) - Body ground Always 10 kΩ or higher
W3-1 (GL3) or 3 (No. 1 glow plug connector terminal) - Body ground Always 10 kΩ or higher
W3-2 (GL4) or 4 (No. 1 glow plug connector terminal) - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



Result:
Proceed to
OK
NG



OK

15.REPLACE GLOW PLUG CONTROLLER

NG

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>1AD-FTV STARTING>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61
HINT:

Check for DTCs in check mode.



Result:
Proceed to
OK
NG



OK

END

NG

18.REPLACE GLOW PLUG ASSEMBLY
18.REPLACE GLOW PLUG ASSEMBLY
a.

Replace the glow plug assembly.

Click hereEngine / Hybrid System>1AD-FTV STARTING>GLOW PLUG>REMOVAL


Result:
Proceed to
NEXT



NEXT

22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 GLOW PLUG CONNECTOR)
a.
A275104
0.719,2.667 1.104,2.917 0.385,0.25 0.75,3.844 1.135,4.094 0.385,0.25 0.875,1.281 1.135,0.969 true 1.458,1.604 1.719,1.292 true 2.042,1.906 2.302,1.594 true 2.625,2.229 2.885,1.917 true 1.333,3.198 1.594,2.885 true 2.083,3.188 1.854,2.875 true 1.365,4.375 1.625,4.063 true 2.125,4.375 1.896,4.063 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *1 0.49,2.115 0.802,2.271 0.313,0.156 10 false *a 0.792,1.271 1.104,1.427 0.313,0.156 10 false 1 1.385,1.594 1.698,1.75 0.313,0.156 10 false 2 1.958,1.885 2.271,2.042 0.313,0.156 10 false 3 2.552,2.198 2.865,2.354 0.313,0.156 10 false 4 0.802,2.719 1.198,2.906 0.396,0.188 10 false W2 0.823,3.885 1.208,4.063 0.385,0.177 10 false W3 1.188,3.219 1.583,3.406 0.396,0.188 10 false GL1 2,3.208 2.396,3.396 0.396,0.188 10 false GL2 1.188,4.385 1.583,4.573 0.396,0.188 10 false GL3 2.052,4.385 2.448,4.573 0.396,0.188 10 false GL4
*1 No. 1 Glow Plug Connector
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect connectors of the glow plug controller.


b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W2-1 (GL1) or 1 (No. 1 glow plug connector terminal) - Body ground Always 10 kΩ or higher
W2-2 (GL2) or 2 (No. 1 glow plug connector terminal) - Body ground Always 10 kΩ or higher
W3-1 (GL3) or 3 (No. 1 glow plug connector terminal) - Body ground Always 10 kΩ or higher
W3-2 (GL4) or 4 (No. 1 glow plug connector terminal) - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



Result:
Proceed to
OK
NG



OK

20.REPLACE GLOW PLUG CONTROLLER

NG

21.REPAIR OR REPLACE HARNESS OR CONNECTOR
20.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>1AD-FTV STARTING>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61
HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END