The intake air temperature sensor (turbo) senses the intake air temperature after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).
The intake air temperature sensor (turbo) is powered by a 5 V supply from the THIA terminal of the ECM, via resistor R. Resistor R and the intake air temperature sensor (turbo) are connected in series. When the resistance value of the sensor changes in accordance with changes in the intake air temperature, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P007C | Charge Air Cooler Temperature Sensor Circuit Low | Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds.
(1 trip detection logic) |
·
Short in intake air temperature sensor (turbo) circuit ·
Intake air temperature sensor (turbo) ·
ECM |
Comes on | DTC stored |
| P007D | Charge Air Cooler Temperature Sensor Circuit High | Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds.
(1 trip detection logic) |
·
Open in intake air temperature sensor (turbo) circuit ·
Intake air temperature sensor (turbo) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P007C | Intake Air Temp (Turbo) |
| P007D |
If DTC P007C or P007D is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P007C | Ignition switch ON for 1 second |
| P007D |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
| Tester Display |
|---|
| Intake Air Temp (Turbo) |
Read the value.
Same as air temperature near intake manifold.
| Proceed to |
|---|
| -40°C (-40°F) |
| 140°C (284°F) or higher |
| OK (same as air temperature near intake manifold) |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or higher.
-40°C (-40°F)
140°C (284°F) or higher
OK (same as air temperature near intake manifold)
| *1 | Intake Air Temperature Sensor (Turbo) |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Intake Air Temperature Sensor (Turbo)) |
Disconnect the intake air temperature sensor (turbo) connector.
Connect terminals 1 and 2 of the intake air temperature sensor (turbo) wire harness side connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
| Tester Display |
|---|
| Intake Air Temp (Turbo) |
Read the value.
140°C (284°F) or higher
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (turbo).
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A54-2 - B76-113 (THIA) | Always | Below 1 Ω |
| A54-1 - B76-90 (ETHI) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor (turbo) connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
| Tester Display |
|---|
| Intake Air Temp (Turbo) |
Read the value.
-40°C (-40°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (turbo).
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A54-2 or B76-113 (THIA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON for 1 second.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT