Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  P0340  Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.

The G signal plate (timing sprocket) has one tooth on its outer circumference and is installed on the camshaft. When the camshaft rotates, the protrusion on the signal plate and the air gap on the pickup coil change, causing fluctuations in the magnetic field that generate a voltage in the pickup coil.

The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G signal, and detects the crankshaft angle based on the NE signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) STA on:
No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more.
(2 trip detection logic)
STA off:
Camshaft position sensor signal is not input with an engine speed of 650 rpm or more.
(1 trip detection logic)
STA off:
Phase deviation in crankshaft and camshaft position sensor signals with an engine speed of 650 to 3000 rpm occurs a certain number of times.
(1 trip detection logic)
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Crankshaft position sensor

·

Camshaft timing gear or sprocket

·

ECM


Comes on DTC Stored

HINT:

If DTC P0340 is stored, the following symptoms may appear:

·

Difficult starting

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0340
·

Crank engine for 4 seconds (STA on)

·

Idle engine for 1 second (STA off)



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).


HINT:
·

After performing the inspection procedure for the camshaft position sensor, if DTC P0340 is output again, check the following items related to the crankshaft position sensor.

·

Installation condition of the crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

Connection of the crankshaft position sensor connector


·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR
a.

Inspect the camshaft position sensor.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>CAMSHAFT POSITION SENSOR>INSPECTION

Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

10.REPLACE CAMSHAFT POSITION SENSOR
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B26-1 - B76-80 (G+) Always Below 1 Ω
B26-2 - B76-79 (G-) Always Below 1 Ω
B26-1 or B76-80 (G+) - Body ground Always 10 kΩ or higher
B26-2 or B76-79 (G-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
A208464
0.401,1.758 0.649,1.91 0.249,0.152 10 OK 2.664,1.768 2.912,1.92 0.249,0.152 10 NG

Check the sensor installation.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.CHECK CAMSHAFT TIMING SPROCKET

NG

8.SECURELY REINSTALL SENSOR
4.CHECK CAMSHAFT TIMING SPROCKET
a.

Check the condition of the timing sprocket.

OK:

Timing sprocket does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR CIRCUIT)

NG

7.REPLACE CAMSHAFT TIMING SPROCKET
5.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR CIRCUIT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Start the engine and idle it for 4 seconds or more.


g.

Turn the GTS on.


h.

Check the engine condition while wiggling the crankshaft position sensor wire harness for 4 seconds or more when idling.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

j.

Read the DTCs.

Result:
Result Proceed to
Except below A
There are problem such as rough idle or engine stall when wire harness is wiggled, or DTC is output* B


HINT:

*: As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE




A

6.REPLACE ECM

B

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE CAMSHAFT TIMING SPROCKET
a.

Replace the camshaft timing sprocket.

Click hereEngine / Hybrid System>2AD-FTV ENGINE MECHANICAL>CAMSHAFT>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.SECURELY REINSTALL SENSOR

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE CAMSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and idle it for 4 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END