Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met for 20 seconds
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
(1 trip detection logic)
·

ST relay circuit

·

Park/neutral position switch assembly*1

·

Clutch pedal switch assembly*2


Comes on DTC stored

*1: for Automatic Transaxle

*2: for Manual Transaxle

Related Data List
DTC No. Data List
P0617 Starter Signal

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0617 Drive vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or higher

WIRING DIAGRAM

A284211
0.177,0.135 4.948,0.375 4.771,0.24 12 false w/ Entry and Start System: 0.125,2.427 0.583,2.625 0.458,0.198 10 false G82 0.135,2.635 2.385,3.094 2.25,0.458 10 false Certification ECU (Smart Key ECU Assembly) 4.406,2.406 5.563,3.156 1.156,0.75 10 false Park/Neutral Position Switch Assembly 5.719,1.594 6.333,1.792 0.615,0.198 10 false NSW*1 1.448,1.073 1.833,1.323 0.385,0.25 10 false NE 1.385,2.115 2,2.313 0.615,0.198 10 false STA 5.677,3.688 6.292,3.885 0.615,0.198 10 false STA 6.063,5.01 6.677,5.208 0.615,0.198 10 false ECM 5.698,1.063 6.313,1.26 0.615,0.198 10 false NEO 4.281,2.021 4.74,2.219 0.458,0.198 10 false B36*1 1.26,1.583 1.875,1.781 0.615,0.198 10 false STAR 3.135,1.906 3.594,2.104 0.458,0.198 10 false A4*2 3.146,2.063 3.604,2.26 0.458,0.198 10 false F2*3 3.125,2.292 3.917,3.167 0.792,0.875 10 false Clutch Start Switch Assembly 0.594,4.844 1.438,5.104 0.844,0.26 10 false FL MAIN 0.583,3.813 1.427,4.073 0.844,0.26 10 false ST 2.875,4.573 3.719,4.833 0.844,0.26 10 false ST 0.708,6.823 1.552,7.083 0.844,0.26 10 false Battery 1.5,6.708 2.344,6.969 0.844,0.26 10 false Starter 1.781,5.698 2.625,5.958 0.844,0.26 10 false B6 1.063,5.938 1.906,6.198 0.844,0.26 10 false C4 1.073,5.74 1.917,6 0.844,0.26 10 false 1 1.594,5.688 2.438,5.948 0.844,0.26 10 false 1 2.646,5.073 2.99,5.323 0.344,0.25 10 false 1 2.646,4.115 2.99,4.365 0.344,0.25 10 false 2 2.125,4.115 2.469,4.365 0.344,0.25 10 false 5 2.115,5.052 2.458,5.302 0.344,0.25 10 false 3 2.75,2.073 3.094,2.323 0.344,0.25 10 false 2 2.74,3 3.083,3.25 0.344,0.25 10 false 1 4.063,2.052 4.406,2.302 0.344,0.25 10 false 4 4.042,2.99 4.385,3.24 0.344,0.25 10 false 9 5.344,1.063 5.719,1.323 0.375,0.26 10 false A61 5.354,1.583 5.729,1.844 0.375,0.26 10 false B76 5.354,3.771 5.729,4.031 0.375,0.26 10 false A61 5.365,3.583 5.74,3.844 0.375,0.26 10 false 43 5.385,1.406 5.76,1.667 0.375,0.26 10 false 38 5.396,0.875 5.771,1.135 0.375,0.26 10 false 10 3.063,5.667 5.792,5.906 2.729,0.24 10 false *1: for Automatic Transaxle 3.052,6.052 5.781,6.292 2.729,0.24 10 false *2: for LHD with Manual Transaxle 3.063,6.417 5.792,6.656 2.729,0.24 10 false *3: for RHD with Manual Transaxle 1.771,0.958 2.146,1.219 0.375,0.26 10 false 16 1.802,1.49 2.177,1.75 0.375,0.26 10 false 5 1.792,1.979 2.167,2.24 0.375,0.26 10 false 7 4.01,2.313 4.469,2.51 0.458,0.198 10 false B 4.021,2.771 4.479,2.969 0.458,0.198 10 false L

A284212
4.281,2.177 5.302,2.958 1.021,0.781 10 false Park/Neutral Position Switch Assembly 2.729,2.375 3.75,3.156 1.021,0.781 10 false Clutch Start Switch Assembly 4.313,1.927 4.813,2.125 0.5,0.198 10 false B36*1 2.75,2.115 3.25,2.313 0.5,0.198 10 false F2*3 0.958,1.813 2.021,2.104 1.063,0.292 10 false Ignition Switch 0.979,1.177 1.458,1.583 0.479,0.406 10 false AM2 1.573,1.177 2.052,1.583 0.479,0.406 10 false ST2 0.552,2.198 1.031,2.604 0.479,0.406 10 false AM2 1.156,3.219 1.635,3.625 0.479,0.406 10 false ST 0.573,4.729 1.49,5.01 0.917,0.281 10 false FL MAIN 5.354,3.552 5.833,3.958 0.479,0.406 10 false A61 1.604,6.51 2.521,6.792 0.917,0.281 10 false Starter 0.729,6.615 1.646,6.896 0.917,0.281 10 false Battery 2.052,3.854 2.26,4.115 0.208,0.26 10 false 5 2.052,4.833 2.26,5.094 0.208,0.26 10 false 3 2.604,4.844 2.813,5.104 0.208,0.26 10 false 1 3.896,1.781 4.104,2.042 0.208,0.26 10 false 4 1.771,5.469 2.25,5.875 0.479,0.406 10 false B6 1.073,5.708 1.552,6.115 0.479,0.406 10 false C4 1.104,5.531 1.313,5.792 0.208,0.26 10 false 1 1.563,5.458 1.771,5.719 0.208,0.26 10 false 1 5.354,1.281 5.833,1.688 0.479,0.406 10 false B76 5.385,1.083 5.865,1.49 0.479,0.406 10 false 38 5.385,3.375 5.865,3.781 0.479,0.406 10 false 43 5.708,3.448 6.188,3.854 0.479,0.406 10 false STA 5.667,1.292 6.354,1.698 0.688,0.406 10 false NSW*1 2.76,1.927 3.26,2.125 0.5,0.198 10 false F4*2 3.656,5.167 6.208,5.479 2.552,0.313 10 false *1: for Automatic Transaxle 3.656,5.531 6.208,5.844 2.552,0.313 10 false *2: for LHD with Manual Transaxle 3.667,5.896 6.219,6.208 2.552,0.313 10 false *3: for RHD with Manual Transaxle 2.344,1.792 2.552,2.052 0.208,0.26 10 false 2 2.365,2.792 2.573,3.052 0.208,0.26 10 false 1 3.854,2.781 4.063,3.042 0.208,0.26 10 false 9 0.677,1.604 1.156,2.01 0.479,0.406 10 false G4 0.823,1.146 1.031,1.406 0.208,0.26 10 false 4 1.938,1.135 2.146,1.396 0.208,0.26 10 false 2 2.552,3.875 2.76,4.135 0.208,0.26 10 false 2 0.125,0.115 5.083,0.354 4.958,0.24 12 false w/o Entry and Start System: 3.854,2.052 4.354,2.25 0.5,0.198 10 false B 3.854,2.531 4.354,2.729 0.5,0.198 10 false L

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).


HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to the Problem Symptoms Table (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

NOTICE:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result:
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON (w/ entry and start system) B
ON (w/o entry and start system) C




A

B

2.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

C

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
2.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (ECM - clutch start switch assembly - certification ECU (smart key ECU assembly) - ST relay).


Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER DTC OUTPUT RECURS
3.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the DTCs.

Result:
Proceed to
DTC P0617 is output
DTC is not output




DTC P0617 is output

4.REPLACE ECM

DTC is not output

END

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER DTC OUTPUT RECURS
5.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

8.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (ECM - clutch start switch assembly - ignition or starter switch assembly - ST relay).


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER DTC OUTPUT RECURS
8.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
a.

Replace the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AD-FTV STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER DTC OUTPUT RECURS