| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P062F | Internal Control Module EEPROM Error | When any condition below is met (1 trip detection logic):
·
Injector compensation code is not registered. ·
Wrong injector compensation code is registered. ·
Injector pilot quantity learning value is not registered. ·
Crank time compensation learning value is not registered.*1 |
·
Injector compensation code ·
Injector pilot quantity learning value ·
Crank time compensation learning value ·
ECM |
Comes on | DTC stored |
*1: When this malfunction occurs, the MIL does not illuminate.
When a fuel injector is replaced, the new fuel injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing fuel injector compensation codes must be input into the new ECM.
Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.
When a fuel injector is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing fuel injector pilot quantity learning values must be input into the new ECM.
When replacing the ECM with a new one, if the injector compensation code and/or injector pilot quantity learning value are not entered, DTC P062F will be stored.
When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:
Prior to replacing the ECM, use the GTS to read and save each learning value and code from the original ECM (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION).
After installing a new ECM, input the saved learning values and codes into the new ECM using the GTS (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION).
Turn the ignition switch off and turn the GTS off.
Wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTC P062F stored in the ECM using the GTS (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>DTC CHECK / CLEAR).
Each fuel injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector.
When you first turn ON the ignition switch after replacing the ECM and other component(s), DTC P062F is stored. Manually clear the DTC upon completion of compensation code registration.
| Replacement Part | Utility Item |
|---|---|
| ECM |
|
| Injector |
|
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P062F | Ignition switch ON for 1 second |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION
| Tester Display |
|---|
| Learning Values Confirmation |
| Result | Proceed to |
|---|---|
| The injector compensation codes are not input | A |
| The injector compensation codes registered in the ECM are different than the codes imprinted on the injectors | |
| The pilot quantity learning values are set to the default values. | B |
| Except above | C |
When the fuel injector pilot quantity learning values are set to the default values, "7FFF" is displayed.
A
B
C
Register the injector compensation code.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the GTS and replacing the old ECM with a new one, "Learning Values Write" was not performed using the GTS causing this DTC to be output.
Install the old ECM.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the intelligent GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Save.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION
| Tester Display |
|---|
| Learning Values Save |
Remove the old ECM.
Install the new ECM.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Write.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION
| Tester Display |
|---|
| Learning Values Write |
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Confirmation.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION
| Tester Display |
|---|
| Learning Values Confirmation |
| Result | Proceed to |
|---|---|
| The pilot quantity learning values are set to the default values. | A |
| Except above | B |
When the fuel injector pilot quantity learning values are set to the default values, "7FFF" is displayed.
A
B
Perform the pilot quantity learning.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and leave the vehicle for 30 seconds or more.
Turn the ignition switch to ON for 1 second.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Proceed to |
|---|
| DTC is not output |
| DTC P062F is output |
DTC is not output
DTC P062F is output
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and leave the vehicle for 30 seconds or more.
Turn the ignition switch to ON for 1 second.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT