Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  P2610  ECM / PCM Internal Engine Off Timer Performance  


DESCRIPTION

The soak timer measures the engine off soak time, which is the time elapsed after the engine switch has been turned off. The ECM uses the engine off soak time to monitor some systems for malfunction detection.

If necessary, the soak timer may activate the ECM to perform certain malfunction checks that can only be performed after the engine stopped. The soak timer is built into the ECM.

A284167
2.51,4.531 3.594,4.729 1.083,0.198 10 false EFI MAIN NO. 1 1.094,3.833 2.177,4.031 1.083,0.198 10 false EFI MAIN NO. 1 0.594,1.219 0.917,1.417 0.323,0.198 10 false IG2 2.26,1.406 2.583,1.604 0.323,0.198 10 false IG2 3.573,0.677 3.896,0.875 0.323,0.198 10 false IGN 4.365,5.458 5.448,5.656 1.083,0.198 10 false MREL 5,0.76 6.083,0.958 1.083,0.198 10 false Soak Timer IC 5.01,2.979 6.094,3.177 1.083,0.198 10 false Power Source IC 4.99,5.208 6.396,5.573 1.406,0.365 10 false Main Relay Control IC 4.5,2.969 4.844,3.135 0.344,0.167 10 false +B2 4.542,3.552 4.885,3.719 0.344,0.167 10 false +B 5.458,6.302 6.542,6.5 1.083,0.198 10 false ECM 1.604,2.594 4.396,2.885 2.792,0.292 10 false from Ignition or Starter Switch Assembly*2 1.583,1.969 4.521,2.406 2.938,0.438 10 false from Certification ECU (Smart Key ECU Assembly)*1 1.448,5.896 4.24,6.188 2.792,0.292 10 false *1: w/ Entry and Start System 1.479,6.302 4.271,6.594 2.792,0.292 10 false *2: w/o Entry and Start System 0.604,4.604 1.688,4.802 1.083,0.198 10 false FL MAIN 0.667,5.417 1.75,5.615 1.083,0.198 10 false Battery 4.375,0.406 5.188,0.781 0.813,0.375 10 false IGSW

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2610 ECM / PCM Internal Engine Off Timer Performance ECM internal malfunction (2 trip detection logic). ECM Comes on DTC stored

MONITOR DESCRIPTION

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


HINT:
·

DTC P2610 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is necessary.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Start the engine and wait for 10 minutes or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

Powertrain > Engine > Trouble Codes
50001 61

g.

If no pending DTC is output, the repair has been successfully completed.


Result:
Proceed to
NEXT



NEXT

END