Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor for the intake camshaft (VV1 signal) consists of a magnet and MRE (Magneto Resistance Element).

The camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection and injection timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor Circuit Malfunction When one of the following conditions is met:
·

No camshaft position sensor signal to the ECM while cranking (2 trip detection logic).

·

A missing camshaft position sensor signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic).


·

Open or short in camshaft position sensor circuit (for intake camshaft)

·

Camshaft position sensor (for intake camshaft)

·

Intake camshaft

·

Valve timing

·

ECM


Comes on DTC stored
P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) The output voltage of the camshaft position sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor circuit (for intake camshaft)

·

Camshaft position sensor (for intake camshaft)

·

ECM


Comes on DTC stored
P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) The output voltage is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor circuit (for intake camshaft)

·

Camshaft position sensor (for intake camshaft)

·

ECM


Comes on DTC stored

A255508E19
0.104,0.042 0.708,0.198 0.604,0.156 10 5 V/DIV. 0.104,0.698 0.427,0.865 0.323,0.167 10 CH1 0.125,1.479 0.448,1.646 0.323,0.167 10 CH2 0.052,0.865 0.427,1.01 0.375,0.146 10 (VV1) 0.063,1.625 0.458,1.771 0.396,0.146 10 (EV1) 3.042,0.813 3.385,0.958 0.344,0.146 10 GND 3.042,1.583 3.385,1.729 0.344,0.146 10 GND 1.25,1.885 2,2.063 0.75,0.177 10 20 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

VV1 stands for the camshaft position sensor signal (for intake camshaft), and EV1 stands for the camshaft position sensor signal (for exhaust camshaft).



ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Start the engine and run it at idle for 10 seconds or more.


WIRING DIAGRAM

A255253E20
1.083,1.927 1.417,2.073 0.333,0.146 10 B39 1.083,2.083 4.219,2.281 3.135,0.198 10 Camshaft Position Sensor (for Intake Camshaft) 5.177,0.417 5.573,0.563 0.396,0.146 10 VCV1 5.708,2.198 6.031,2.375 0.323,0.177 10 B77 5.708,2.365 6.052,2.552 0.344,0.188 10 ECM 4.823,0.417 5.104,0.604 0.281,0.188 10 113 4.896,0.958 5.104,1.156 0.208,0.198 10 82 4.823,1.49 5.073,1.656 0.25,0.167 10 114 2.646,0.396 2.771,0.563 0.125,0.167 10 3 2.646,0.948 2.75,1.125 0.104,0.177 10 1 2.646,1.49 2.75,1.635 0.104,0.146 10 2 2.323,0.406 2.542,0.583 0.219,0.177 10 VC 2.219,0.948 2.552,1.094 0.333,0.146 10 VV1+ 2.24,1.49 2.531,1.625 0.292,0.135 10 VV1- 5.177,0.958 5.552,1.125 0.375,0.167 10 VV1+ 5.177,1.49 5.552,1.656 0.375,0.167 10 VV1- 1.615,0.896 1.75,1.063 0.135,0.167 10 * 0.063,2.417 4.396,2.604 4.333,0.188 10 *: MRE (Outputs a voltage corresponding to changes in magnetic flux)

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR)
a.
A194108C31
0.365,2.302 0.781,2.573 0.417,0.271 2.01,2.51 2.292,3.073 false 0.208,0.198 0.396,0.375 0.188,0.177 10 *a 0.448,2.354 0.719,2.5 0.271,0.146 10 B39 2.219,3.104 2.542,3.271 0.323,0.167 10 VC
*a Front view of wire harness connector
(to Camshaft Position Sensor for Intake Camshaft)


Disconnect the camshaft position sensor for intake camshaft connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B39-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor for intake camshaft connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B39-1 (VV1+) - B77-82 (VV1+) Always Below 1 Ω
B39-2 (VV1-) - B77-114 (VV1-) Always Below 1 Ω
B39-1 (VV1+) or B77-82 (VV1+) - Body ground Always 10 kΩ or higher
B39-2 (VV1-) or B77-114 (VV1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT)
a.
B319222E02
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

Check the camshaft position sensor for intake camshaft installation.

OK:

Camshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR

4.INSPECT CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the intake camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the intake camshaft.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

OK

6.REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

NG

6.REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)
a.

Replace the camshaft position sensor (for intake camshaft).

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0340, P0342 or P0343 is output A
DTC is not output B


HINT:

If the engine does not start, replace the ECM.




A

B

END

8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor for intake camshaft connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B39-3 (VC) - B77-113 (VCV1) Always Below 1 Ω
B39-3 (VC) or B77-113 (VCV1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR