1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
51443
3.REMOVE REAR ENGINE UNDER COVER RH
12601B
4.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
17705
5.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
6.REMOVE AIR CLEANER CASE
16470
7.DISCONNECT RADIATOR RESERVOIR ASSEMBLY
82121
8.DISCONNECT ENGINE WIRE
Disconnect the connectors and clamps, remove the bolts and nuts and disconnect the engine wire from the engine.
19500
9.REMOVE IGNITION COIL ASSEMBLY
11301K
10.REMOVE CRANKSHAFT POSITION SENSOR
11201
11.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
12.SET NO. 1 CYLINDER TO TDC/COMPRESSION
| *1 | Paint Mark |
| *2 | Matchmark |
| *3 | Timing Notch (Groove) |
Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover are aligned.
Check that each matchmark of the camshaft timing gear and camshaft timing exhaust gear are aligned with each matchmark located as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.
Place paint marks on the chain in alignment with the timing marks on the camshaft timing gear and camshaft timing exhaust gear.
11324
13.REMOVE TIMING CHAIN COVER PLATE
Remove the 4 bolts, timing chain cover plate and gasket.
13540
14.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
| *a | Approximately 10° |
Turn the crankshaft approximately 10° clockwise.
| *a | Approximately 10° |
Turn the crankshaft approximately 10° counterclockwise.
| *1 | Pin |
Align the holes of the stopper plate and tensioner, and insert a pin into the stopper plate hole to lock the tensioner.
| *a | Approximately 10° |
Turn the crankshaft approximately 10° clockwise.
Remove the 2 bolts, No. 1 chain tensioner and gasket.
Make sure not to drop the gasket inside the timing chain cover.
| *a | Approximately 10° |
Turn the crankshaft approximately 10° counterclockwise.
13566B
15.REMOVE TIMING CHAIN GUIDE
16.REMOVE TIMING CHAIN COVER TIGHT PLUG
13050
17.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
Hold the hexagonal portion of the camshaft with a wrench and remove the bolt from the camshaft.
Be careful not to damage the cylinder head or spark plug tube with the wrench.
Separate the camshaft timing gear assembly from the camshaft.
| *1 | Narrow |
| *2 | Wide |
Remove the timing chain from the camshaft timing gear assembly, and turn the camshaft timing gear assembly approximately 180°.
Remove the camshaft timing gear assembly.
Do not disassemble the camshaft timing gear.
18.REMOVE CAMSHAFT BEARING CAP
Using several steps, remove the 11 bearing cap bolts in the sequence shown in the illustration.
Using several steps, remove the 10 bearing cap bolts in the sequence shown in the illustration.
Remove the 5 camshaft bearing caps.
Arrange the removed parts in the correct order.
13511
19.REMOVE CAMSHAFT
Remove the camshaft from the camshaft housing.
13512
20.REMOVE NO. 2 CAMSHAFT
Hold up the chain and remove the No. 2 camshaft from the camshaft housing.
Suspend the chain with a string or equivalent as shown in the illustration.
Be careful not to drop the chain inside the timing chain cover.
13070A
21.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Remove the flange bolt and camshaft timing exhaust gear assembly.
Do not disassemble the camshaft timing exhaust gear.
15678A
22.REMOVE OIL CONTROL VALVE FILTER
11811
23.REMOVE NO. 1 CAMSHAFT BEARING
11821
24.REMOVE NO. 2 CAMSHAFT BEARING