Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049188 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1451/51  Compressor Solenoid Circuit  


DESCRIPTION

In this circuit, the compressor assembly with pulley*1 or cooler compressor assembly*2 receives a refrigerant compression demand signal from the air conditioning amplifier assembly.

Based on this signal, the compressor assembly with pulley*1 or cooler compressor assembly*2 changes the amount of compressor output.

*1: w/o Magnet Clutch

*2: w/ Magnet Clutch



DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1451/51 Compressor Solenoid Circuit Open or short in compressor solenoid circuit
·

Compressor assembly with pulley (w/o Magnet Clutch)

·

Cooler compressor assembly (w/ Magnet Clutch)

·

Harness or connector

·

Air conditioning amplifier assembly


- -

HINT:

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E229254E35
5.01,0.792 5.104,0.969 0.094,0.177 10 false 2 3.833,0.792 3.927,0.969 0.094,0.177 10 false 2 2.448,0.792 2.542,0.969 0.094,0.177 10 false 1 5.229,0.885 5.688,1.063 0.458,0.177 10 false SOL+ 3.385,0.792 3.76,0.969 0.375,0.177 10 false SOL+ 2.625,0.792 2.969,0.969 0.344,0.177 10 false SOL- 4.823,3.5 5.167,3.677 0.344,0.177 10 false G81 4.823,3.667 6.469,4 1.646,0.333 10 false Air Conditioning Amplifier Assembly 2.104,1.49 4.458,1.708 2.354,0.219 10 false Compressor Assembly with Pulley*1 2.104,1.333 2.49,1.583 0.385,0.25 10 false B30 2.104,1.813 4.458,2.031 2.354,0.219 10 false Cooler Compressor Assembly*2 0.229,4.427 2.583,4.646 2.354,0.219 10 false *2: w/ Magnet Clutch 0.229,4.146 2.583,4.365 2.354,0.219 10 false *1: w/o Magnet Clutch

CAUTION / NOTICE / HINT

NOTICE:

When the battery is disconnected or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Regulator Control Current Solenoid valve control current Min.: 0 A
Max.: 0.997 A
Value changes between 0 A and 0.997 A in accordance with solenoid valve operation -
Body Electrical > Air Conditioner > Data List
Tester Display
Regulator Control Current
50003 121 53
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG (w/o Magnet Clutch) C
NG (w/ Magnet Clutch) D



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.INSPECT COMPRESSOR ASSEMBLY WITH PULLEY

D

5.INSPECT COOLER COMPRESSOR ASSEMBLY
2.INSPECT COMPRESSOR ASSEMBLY WITH PULLEY

OK

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY - BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY - BODY GROUND)
a.
E269947C01
1.521,0.313 1.938,0.563 0.417,0.25 0.927,1.51 1.198,1.51 1.198,1.51 1.531,1.24 true 0.042,0.052 0.354,0.25 0.313,0.198 10 *a 0.49,1.427 0.906,1.635 0.417,0.208 10 SOL- 1.604,0.354 1.917,0.552 0.313,0.198 10 B30
*a Front view of wire harness connector
(to Compressor Assembly with Pulley)


Disconnect the compressor assembly with pulley connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B30-1 (SOL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the G81 air conditioning amplifier assembly connector.


b.

Disconnect the B30 compressor assembly with pulley connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G81-2 (SOL+) - B30-2 (SOL+) Always Below 1 Ω
G81-2 (SOL+) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT COOLER COMPRESSOR ASSEMBLY
a.

b.

Inspect the cooler compressor assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR(for 2AR-FE)>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - BODY GROUND)
a.
E269947C01
1.521,0.313 1.938,0.563 0.417,0.25 0.927,1.51 1.198,1.51 1.198,1.51 1.531,1.24 true 0.042,0.052 0.354,0.25 0.313,0.198 10 *a 0.49,1.427 0.906,1.635 0.417,0.208 10 SOL- 1.604,0.354 1.917,0.552 0.313,0.198 10 B30
*a Front view of wire harness connector
(to Cooler Compressor Assembly)


Disconnect the cooler compressor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B30-1 (SOL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the G81 air conditioning amplifier assembly connector.


b.

Disconnect the B30 cooler compressor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G81-2 (SOL+) - B30-2 (SOL+) Always Below 1 Ω
G81-2 (SOL+) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR