Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ Occupant Classification System)
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0066372 AIRBAG SYSTEM(w/ Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ Occupant Classification System)  B1642/81  Lost Communication with Side Satellite Sensor Bus RH  B1647/82  Lost Communication with Side Satellite Sensor Bus LH  


DESCRIPTION

The circuit for the side collision sensor LH or RH (to determine deployment of the front seat airbag assembly LH or RH and curtain shield airbag assembly LH or RH) is composed of the airbag sensor assembly, rear airbag sensor LH or RH and door side airbag sensor LH or RH.

The door side airbag sensor LH or RH and rear airbag sensor LH or RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1642/82 or B1647/82 is stored when a malfunction is detected in the circuit for the side satellite sensor bus LH or RH (to determine deployment of the front seat airbag assembly LH or RH and curtain shield airbag assembly LH or RH).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1642/81 Lost Communication with Side Satellite Sensor Bus RH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus RH for 2 seconds.

·

A door side airbag sensor RH malfunction.

·

A rear airbag sensor RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire RH

·

Door side airbag sensor RH

·

Rear airbag sensor RH

·

Airbag sensor assembly


B1647/82 Lost Communication with Side Satellite Sensor Bus LH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus LH for 2 seconds.

·

A door side airbag sensor LH malfunction.

·

A rear airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

No. 2 floor wire

·

Front door wire LH

·

Door side airbag sensor LH

·

Rear airbag sensor LH

·

Airbag sensor assembly



WIRING DIAGRAM

C279110E03
0.052,0.052 1.406,0.385 1.354,0.333 12 false for RH Side: 1.083,0.656 1.531,0.844 0.448,0.188 10 false BCR+ 1.094,1.052 1.51,1.24 0.417,0.188 10 false BCR- 1.094,1.833 1.531,2.021 0.438,0.188 10 false BDR+ 1.094,2.26 1.521,2.438 0.427,0.177 10 false BDR- 2.281,1.833 2.615,2.042 0.333,0.208 10 false IM1 3.115,1.823 3.573,2.01 0.458,0.188 10 false BDR+ 3.125,2.271 3.583,2.458 0.458,0.188 10 false BDR- 5.667,0.635 6.125,0.823 0.458,0.188 10 false BBR+ 5.677,1.073 6.135,1.26 0.458,0.188 10 false BBR- 5.375,2.01 6.969,2.219 1.594,0.208 10 false Airbag Sensor Assembly 0.49,2.771 2.063,2.979 1.573,0.208 10 false Rear Airbag Sensor RH 5.406,1.865 5.865,2.052 0.458,0.188 10 false M25 3.052,2.625 3.406,2.833 0.354,0.208 10 false I13 0.49,2.625 0.75,2.823 0.26,0.198 10 false M7 1.552,0.552 1.771,0.729 0.219,0.177 10 false 4 1.552,0.969 1.74,1.156 0.188,0.188 10 false 3 1.531,1.75 1.708,1.927 0.177,0.177 10 false 1 1.552,2.177 1.75,2.365 0.198,0.188 10 false 2 5.427,0.563 5.646,0.75 0.219,0.188 10 false 24 5.438,0.979 5.677,1.167 0.24,0.188 10 false 23 2.292,2.25 2.625,2.458 0.333,0.208 10 false IM1 2.354,2.083 2.531,2.26 0.177,0.177 10 false 1 2.344,1.667 2.542,1.854 0.198,0.188 10 false 2 2.948,1.74 3.146,1.927 0.198,0.188 10 false 2 2.948,2.177 3.125,2.354 0.177,0.177 10 false 1 3.031,2.781 4.875,2.99 1.844,0.208 10 false Door Side Airbag Sensor RH

C279110E04
0.052,0.052 1.208,0.365 1.156,0.313 12 false for LH Side: 1.083,0.656 1.531,0.844 0.448,0.188 10 false BCL+ 1.094,1.052 1.51,1.24 0.417,0.188 10 false BCL- 1.094,1.833 1.531,2.021 0.438,0.188 10 false BDL+ 1.094,2.26 1.521,2.438 0.427,0.177 10 false BDL- 2.281,1.844 2.615,2.052 0.333,0.208 10 false JN1 3.115,1.823 3.573,2.01 0.458,0.188 10 false BDL+ 3.125,2.271 3.583,2.458 0.458,0.188 10 false BDL- 5.667,0.635 6.125,0.823 0.458,0.188 10 false BBL+ 5.677,1.073 6.135,1.26 0.458,0.188 10 false BBL- 5.531,2.01 7.156,2.198 1.625,0.188 10 false Airbag Sensor Assembly 0.521,2.792 2.094,3 1.573,0.208 10 false Rear Airbag Sensor LH 5.542,1.875 6,2.063 0.458,0.188 10 false N21 3.01,2.604 3.365,2.813 0.354,0.208 10 false J12 0.531,2.635 0.792,2.833 0.26,0.198 10 false N9 1.552,0.552 1.771,0.729 0.219,0.177 10 false 4 1.552,0.969 1.74,1.156 0.188,0.188 10 false 3 1.531,1.75 1.708,1.927 0.177,0.177 10 false 1 1.552,2.177 1.75,2.365 0.198,0.188 10 false 2 5.427,0.552 5.646,0.74 0.219,0.188 10 false 17 5.438,0.979 5.677,1.167 0.24,0.188 10 false 18 2.292,2.26 2.625,2.469 0.333,0.208 10 false JN1 2.354,2.083 2.531,2.26 0.177,0.177 10 false 1 2.344,1.667 2.542,1.854 0.198,0.188 10 false 3 2.948,1.74 3.146,1.927 0.198,0.188 10 false 2 2.948,2.177 3.125,2.354 0.177,0.177 10 false 1 3.01,2.75 4.885,2.958 1.875,0.208 10 false Door Side Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1642/81 is output
DTC B1647/82 is output
DTC B1642/81 and B1647/82 are not output


HINT:

Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.




DTC B1642/81 is output

2.CHECK CONNECTION OF CONNECTORS

DTC B1647/82 is output

11.CHECK CONNECTION OF CONNECTORS

DTC B1642/81 and B1647/82 are not output

2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and rear airbag sensor RH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

3.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and rear airbag sensor RH.


b.
C208244C09
0.354,1.333 0.667,1.49 0.313,0.156 10 *1 2.115,1.792 2.427,1.948 0.313,0.156 10 *2 1.521,1.052 1.833,1.208 0.313,0.156 10 *3
*1 Rear Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and rear airbag sensor RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

4.CHECK REAR AIRBAG SENSOR RH CIRCUIT

The connectors are deformed or damaged

REPLACE FLOOR WIRE

4.CHECK REAR AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C256267C06
2.781,0.552 3.135,0.771 0.354,0.219 4.979,0.604 5.333,0.823 0.354,0.219 5.479,1.385 5.865,1.073 false 3.344,1.302 3.906,0.885 false 4.542,1.313 4.052,0.854 false 6.563,1.49 5.958,1.073 false 5.917,1.615 5.917,1.469 false 0.49,0.813 0.802,0.969 0.313,0.156 10 false *1 2.063,1.188 2.375,1.344 0.313,0.156 10 false *2 1.198,0.24 1.51,0.396 0.313,0.156 10 false *3 4.552,0.729 4.865,0.885 0.313,0.156 10 false *4 6.813,0.76 7.125,0.917 0.313,0.156 10 false *5 5.844,1.625 6.156,1.781 0.313,0.156 10 false *6 3.792,0.188 4.104,0.344 0.313,0.156 10 false *a 6.146,0.198 6.458,0.354 0.313,0.156 10 false *b 1.854,0.417 2.083,0.573 0.229,0.156 10 false A 1.458,0.615 1.688,0.792 0.229,0.177 10 false B 0.938,0.625 1.167,0.802 0.229,0.177 10 false C 0.583,0.406 0.813,0.583 0.229,0.177 10 false D 2.875,0.583 3.26,0.75 0.385,0.167 10 false M7 5.031,0.635 5.417,0.802 0.385,0.167 10 false M25 3.115,1.354 3.542,1.521 0.427,0.167 10 false BCR- 4.375,1.365 4.802,1.531 0.427,0.167 10 false BCR+ 5.24,1.427 5.667,1.594 0.427,0.167 10 false BBR+ 6.5,1.521 6.927,1.688 0.427,0.167 10 false BBR-
*1 Rear Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M7-4 (BCR+) - Body ground Ignition switch ON Below 1 V
M7-3 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 24 (BBR+) and 23 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-4 (BCR+) - M7-3 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-4 (BCR+) - M7-3 (BCR-) Always 1 MΩ or higher
M7-4 (BCR+) - Body ground Always 1 MΩ or higher
M7-3 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK CONNECTION OF CONNECTOR

NG

9.CHECK FLOOR WIRE
5.CHECK CONNECTION OF CONNECTOR
a.

Check that the connector is properly connected to the door side airbag sensor RH.


Result:
Proceed to
The connector is properly connected
The connector is not properly connected



The connector is properly connected

6.CHECK CONNECTOR

The connector is not properly connected

CONNECT CONNECTOR PROPERLY

6.CHECK CONNECTOR
a.

Disconnect the connector from the door side airbag sensor RH.


b.
C213962C05
0.521,1.615 0.719,1.781 0.198,0.167 10 *1 2.146,1.615 2.344,1.781 0.198,0.167 10 *2
*1 Door Side Airbag Sensor RH
*2 Rear Airbag Sensor RH


Check that the connector (on the door side airbag sensor RH side) is not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

7.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT

The connector is deformed or damaged

REPLACE HARNESS AND CONNECTOR

7.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C256270C01
2.49,0.719 2.865,0.927 0.375,0.208 4.667,0.698 5.042,0.906 0.375,0.208 2.958,1.271 3.448,0.906 false 4.125,1.302 3.625,0.906 false 5.094,1.24 5.583,0.875 false 6.448,1.26 5.74,0.865 false 3.854,1.594 3.583,1.417 false 0.354,1.25 0.667,1.406 0.313,0.156 10 *1 1.875,1.281 2.135,1.458 0.26,0.177 10 *2 4.104,0.75 4.406,0.938 0.302,0.188 10 *3 6.417,0.74 6.729,0.896 0.313,0.156 10 *4 3.458,0.115 3.771,0.271 0.313,0.156 10 *a 5.698,0.135 6.01,0.292 0.313,0.156 10 *b 0.583,0.802 0.896,0.958 0.313,0.156 10 F 0.906,1.021 1.219,1.177 0.313,0.156 10 E 1.104,1.021 1.417,1.177 0.313,0.156 10 D 1.219,1.021 1.531,1.177 0.313,0.156 10 C 1.385,1.021 1.698,1.177 0.313,0.156 10 B 1.74,0.792 2.052,0.948 0.313,0.156 10 A 2.573,0.74 2.833,0.917 0.26,0.177 10 I13 2.573,1.302 3.052,1.5 0.479,0.198 10 BDR- 3.99,1.323 4.469,1.521 0.479,0.198 10 BDR+ 3.896,1.552 4.167,1.729 0.271,0.177 10 *5 4.771,0.729 5.031,0.906 0.26,0.177 10 M7 4.906,1.313 5.385,1.51 0.479,0.198 10 BDR+ 6.365,1.313 6.844,1.51 0.479,0.198 10 BDR-
*1 Door Side Airbag Sensor RH *2 Rear Airbag Sensor RH
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M7-1 (BDR+) - Body ground Ignition switch ON Below 1 V
M7-2 (BDR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-1 (BDR+) - M7-2 (BDR-) Always Below 1 Ω



h.

Disconnect the service wire from connector E.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-1 (BDR+) - M7-2 (BDR-) Always 1 MΩ or higher
M7-1 (BDR+) - Body ground Always 1 MΩ or higher
M7-2 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK REAR AIRBAG SENSOR RH

NG

9.CHECK FLOOR WIRE
8.CHECK REAR AIRBAG SENSOR RH
a.
C146229C17
0.854,0.99 1.021,1.146 0.167,0.156 10 false *1 1.823,1.313 1.99,1.479 0.167,0.167 10 false *2
*1 Rear Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and door side airbag sensor RH.


b.

Interchange the rear airbag sensor RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 90 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1647/82 is output
DTC B1642/81 is output
DTC B1642/81 and B1647/82 are not output


HINT:

Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.



DTC B1647/82 is output

DTC B1642/81 is output

10.CHECK DOOR SIDE AIRBAG SENSOR RH

DTC B1642/81 and B1647/82 are not output

9.CHECK FLOOR WIRE
a.

Disconnect the floor wire connector from the front door wire RH.

C279670C02
5.042,0.667 5.365,0.906 0.323,0.24 2.885,0.635 3.24,0.833 0.354,0.198 5.396,1.25 5.813,0.833 false 6.406,1.24 5.917,0.823 false 4.292,1.104 3.792,0.677 false 3.177,1.125 3.656,0.688 false 3.208,1.531 3.573,1.385 false 0.917,0.75 0.917,0.25 0.917,0.25 1.083,0.25 false 1.333,0.833 1.333,1.333 1.333,1.333 1.167,1.333 false 1.729,0.688 1.885,0.885 0.156,0.198 10 A 1.385,0.927 1.542,1.125 0.156,0.198 10 B 1.094,0.938 1.25,1.135 0.156,0.198 10 C 0.906,0.938 1.063,1.135 0.156,0.198 10 D 0.698,0.938 0.854,1.135 0.156,0.198 10 E 0.365,0.677 0.521,0.875 0.156,0.198 10 F 0.365,1.125 0.594,1.323 0.229,0.198 10 *1 1.635,1.156 1.865,1.354 0.229,0.198 10 *2 1.115,0.188 1.344,0.385 0.229,0.198 10 *3 0.958,1.25 1.188,1.448 0.229,0.198 10 *4 3.594,0.125 3.823,0.323 0.229,0.198 10 *a 5.854,0.146 6.083,0.344 0.229,0.198 10 *b 6.615,0.677 6.844,0.875 0.229,0.198 10 *6 4.25,0.667 4.479,0.865 0.229,0.198 10 *5 2.917,0.646 3.24,0.833 0.323,0.188 10 IM1 5.094,0.677 5.385,0.875 0.292,0.198 10 M7 2.958,1.469 3.188,1.667 0.229,0.198 10 *7 2.708,1.042 3.26,1.219 0.552,0.177 10 BDR+ 5.094,1.281 5.646,1.458 0.552,0.177 10 BDR+ 4.344,1.021 4.896,1.198 0.552,0.177 10 BDR- 6.323,1.26 6.875,1.438 0.552,0.177 10 BDR-
*1 Door Side Airbag Sensor RH *2 Rear Airbag Sensor RH
*3 Front Door Wire RH *4 Floor Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Door Wire RH)
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M7-1 (BDR+) - Body ground Ignition switch ON Below 1 V
M7-2 (BDR-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-1 (BDR+) - M7-2 (BDR-) Always Below 1 Ω



i.

Disconnect the service wire from connector C.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-1 (BDR+) - M7-2 (BDR-) Always 1 MΩ or higher
M7-1 (BDR+) - Body ground Always 1 MΩ or higher
M7-2 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

10.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C171828C15
0.688,1.333 0.854,1.49 0.167,0.156 10 *1 2.365,1.323 2.531,1.49 0.167,0.167 10 *2
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor RH


Interchange the door side airbag sensor RH with LH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 90 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1647/82 is output
DTC B1642/81 is output
DTC B1642/81 and B1647/82 are not output


HINT:

Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


j.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.



DTC B1647/82 is output

DTC B1642/81 is output

DTC B1642/81 and B1647/82 are not output

11.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and rear airbag sensor LH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

12.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

12.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly, rear airbag sensor LH and door side airbag sensor LH.


b.
C208245C06
0.313,1.75 0.625,1.906 0.313,0.156 10 *1 2.104,1.573 2.417,1.729 0.313,0.156 10 *2 1.521,1.042 1.833,1.198 0.313,0.156 10 *3
*1 Rear Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire


Check that the connectors (on the airbag sensor assembly side and rear airbag sensor LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

13.CHECK REAR AIRBAG SENSOR LH CIRCUIT

The connectors are deformed or damaged

REPLACE NO. 2 FLOOR WIRE

13.CHECK REAR AIRBAG SENSOR LH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C256269C03
5.135,0.542 5.542,0.781 0.406,0.24 2.854,0.51 3.26,0.75 0.406,0.24 3.552,1.271 4.031,0.771 false 4.594,1.24 4.177,0.781 false 6.906,1.417 6.563,1.052 false 5.646,1.448 6.448,1.021 false 6.51,1.406 6.51,1.563 false 0.552,1.229 0.865,1.385 0.313,0.156 10 false *1 2.135,1.104 2.448,1.26 0.313,0.156 10 false *2 1.281,0.656 1.594,0.813 0.313,0.156 10 false *3 4.708,0.625 5.021,0.781 0.313,0.156 10 false *4 6.844,0.677 7.156,0.833 0.313,0.156 10 false *5 6.448,1.594 6.76,1.75 0.313,0.156 10 false *6 3.938,0.125 4.25,0.281 0.313,0.156 10 false *a 6.198,0.156 6.51,0.313 0.313,0.156 10 false *b 1.927,0.823 2.24,0.979 0.313,0.156 10 false A 1.563,1.073 1.875,1.229 0.313,0.156 10 false B 1.042,1.063 1.354,1.219 0.313,0.156 10 false C 0.677,0.823 0.99,0.979 0.313,0.156 10 false D 2.979,0.542 3.292,0.698 0.313,0.156 10 false N9 5.208,0.583 5.521,0.74 0.313,0.156 10 false N21 3.344,1.333 3.833,1.521 0.49,0.188 10 false BCL- 5.406,1.479 5.896,1.667 0.49,0.188 10 false BBL- 4.51,1.313 5,1.5 0.49,0.188 10 false BCL+ 6.771,1.479 7.156,1.667 0.385,0.188 10 false BBL+
*1 Rear Airbag Sensor LH *2 Airbag Sensor Assembly
*3 No. 2 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N9-4 (BCL+) - Body ground Ignition switch ON Below 1 V
N9-3 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 17 (BBL+) and 18 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N9-4 (BCL+) - N9-3 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N9-4 (BCL+) - N9-3 (BCL-) Always 1 MΩ or higher
N9-4 (BCL+) - Body ground Always 1 MΩ or higher
N9-3 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK CONNECTION OF CONNECTOR

NG

REPLACE NO. 2 FLOOR WIRE

14.CHECK CONNECTION OF CONNECTOR
a.

Check that the connector is properly connected to the door side airbag sensor LH.


Result:
Proceed to
The connector is properly connected
The connector is not properly connected



The connector is properly connected

15.CHECK CONNECTOR

The connector is not properly connected

CONNECT CONNECTOR PROPERLY

15.CHECK CONNECTOR
a.

Disconnect the connector from the door side airbag sensor LH.


b.
C213962C05
0.521,1.615 0.719,1.781 0.198,0.167 10 *1 2.146,1.615 2.344,1.781 0.198,0.167 10 *2
*1 Door Side Airbag Sensor LH
*2 Rear Airbag Sensor LH


Check that the connector (on the door side airbag sensor LH side) is not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

16.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT

The connector is deformed or damaged

REPLACE HARNESS AND CONNECTOR

16.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C256270C03
2.49,0.719 2.865,0.927 0.375,0.208 4.667,0.698 5.042,0.906 0.375,0.208 2.958,1.271 3.448,0.906 false 4.125,1.302 3.625,0.906 false 5.094,1.24 5.583,0.875 false 6.448,1.26 5.74,0.865 false 3.854,1.594 3.583,1.417 false 0.354,1.25 0.667,1.406 0.313,0.156 10 *1 1.875,1.281 2.135,1.458 0.26,0.177 10 *2 4.104,0.75 4.406,0.938 0.302,0.188 10 *3 6.417,0.74 6.729,0.896 0.313,0.156 10 *4 3.458,0.115 3.771,0.271 0.313,0.156 10 *a 5.698,0.135 6.01,0.292 0.313,0.156 10 *b 0.583,0.802 0.896,0.958 0.313,0.156 10 F 0.906,1.021 1.219,1.177 0.313,0.156 10 E 1.104,1.021 1.417,1.177 0.313,0.156 10 D 1.219,1.021 1.531,1.177 0.313,0.156 10 C 1.385,1.021 1.698,1.177 0.313,0.156 10 B 1.74,0.792 2.052,0.948 0.313,0.156 10 A 2.573,0.74 2.833,0.917 0.26,0.177 10 J12 2.573,1.302 3.052,1.5 0.479,0.198 10 BDL- 3.99,1.323 4.469,1.521 0.479,0.198 10 BDL+ 3.896,1.552 4.167,1.729 0.271,0.177 10 *5 4.771,0.729 5.031,0.906 0.26,0.177 10 N9 4.906,1.313 5.385,1.51 0.479,0.198 10 BDL+ 6.365,1.313 6.844,1.51 0.479,0.198 10 BDL-
*1 Door Side Airbag Sensor LH *2 Rear Airbag Sensor LH
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Rear Airbag Sensor LH)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N9-1 (BDL+) - Body ground Ignition switch ON Below 1 V
N9-2 (BDL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N9-1 (BDL+) - N9-2 (BDL-) Always Below 1 Ω



h.

Disconnect the service wire from connector E.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N9-1 (BDL+) - N9-2 (BDL-) Always 1 MΩ or higher
N9-1 (BDL+) - Body ground Always 1 MΩ or higher
N9-2 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK REAR AIRBAG SENSOR LH

NG

18.CHECK NO. 2 FLOOR WIRE
17.CHECK REAR AIRBAG SENSOR LH
a.
C171812C16
0.677,1.281 0.833,1.448 0.156,0.167 10 false *1 1.823,1.115 2.01,1.281 0.188,0.167 10 false *2
*1 Rear Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and door side airbag sensor LH.


b.

Interchange the rear airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 90 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1642/81 is output
DTC B1647/82 is output
DTC B1642/81 and B1647/82 are not output


HINT:

Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.



DTC B1642/81 is output

DTC B1647/82 is output

19.CHECK DOOR SIDE AIRBAG SENSOR LH

DTC B1642/81 and B1647/82 are not output

18.CHECK NO. 2 FLOOR WIRE
a.

Disconnect the No. 2 floor wire connector from the front door wire LH.

C279671C04
5,0.667 5.323,0.896 0.323,0.229 2.729,0.604 3.115,0.854 0.385,0.25 1.083,1.333 1.333,1.333 1.333,1.333 1.333,0.833 false 1.167,0.25 0.917,0.25 0.917,0.25 0.917,0.75 false 3.177,0.302 3.771,0.625 false 3.177,1.313 3.771,0.854 false 5.438,1.229 5.823,0.833 false 6.302,1.198 5.927,0.833 false 4.385,1.135 4.198,0.823 false 1.698,0.698 1.854,0.896 0.156,0.198 10 false A 1.385,0.906 1.542,1.104 0.156,0.198 10 false B 1.094,0.906 1.25,1.104 0.156,0.198 10 false C 0.969,0.906 1.125,1.104 0.156,0.198 10 false D 0.708,0.896 0.865,1.094 0.156,0.198 10 false E 0.406,0.688 0.563,0.885 0.156,0.198 10 false F 0.271,1.125 0.573,1.344 0.302,0.219 10 false *1 1.646,1.188 1.948,1.406 0.302,0.219 10 false *2 1.198,0.167 1.5,0.385 0.302,0.219 10 false *3 0.917,1.25 1.219,1.469 0.302,0.219 10 false *4 3.625,0.052 3.927,0.271 0.302,0.219 10 false *a 5.865,0.104 6.167,0.323 0.302,0.219 10 false *b 4.427,1.135 4.729,1.354 0.302,0.219 10 false *7 4.354,0.635 4.656,0.854 0.302,0.219 10 false *5 6.708,0.688 7.01,0.906 0.302,0.219 10 false *6 2.792,0.646 3.198,0.885 0.406,0.24 10 false JN1 2.781,1.24 3.25,1.479 0.469,0.24 10 false BDL+ 2.823,0.208 3.292,0.448 0.469,0.24 10 false BDL- 5.052,1.167 5.521,1.406 0.469,0.24 10 false BDL+ 6.354,1.198 6.823,1.438 0.469,0.24 10 false BDL- 5.073,0.688 5.365,0.917 0.292,0.229 10 false N9
*1 Door Side Airbag Sensor LH *2 Rear Airbag Sensor LH
*3 Front Door Wire LH *4 No. 2 Floor Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Door Wire LH)
*b Front view of wire harness connector
(to Rear Airbag Sensor LH)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N9-1 (BDL+) - Body ground Ignition switch ON Below 1 V
N9-2 (BDL-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 3 (BDL+) and 1 (BDL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N9-1 (BDL+) - N9-2 (BDL-) Always Below 1 Ω



i.

Disconnect the service wire from connector C.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N9-1 (BDL+) - N9-2 (BDL-) Always 1 MΩ or higher
N9-1 (BDL+) - Body ground Always 1 MΩ or higher
N9-2 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE NO. 2 FLOOR WIRE

19.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C171828C15
0.688,1.333 0.854,1.49 0.167,0.156 10 *1 2.365,1.323 2.531,1.49 0.167,0.167 10 *2
*1 Door Side Airbag Sensor RH
*2 Rear Airbag Sensor LH


Interchange the door side airbag sensor LH with RH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 90 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1642/81 is output
DTC B1647/82 is output
DTC B1642/81 and B1647/82 are not output


HINT:

Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


j.

Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.



DTC B1642/81 is output

DTC B1647/82 is output

DTC B1642/81 and B1647/82 are not output