The seat position airbag sensor circuit consists of the airbag sensor assembly and seat position airbag sensor.
DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1653/35 | Seat Position Airbag Sensor Circuit Malfunction | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds. ·
A seat position airbag sensor malfunction. ·
An airbag sensor assembly malfunction |
·
No. 2 floor wire ·
Front seat inner belt assembly LH ·
Seat position airbag sensor ·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and seat position airbag sensor.
| Proceed to |
|---|
| Connectors are properly connected |
| Connectors are not properly connected |
Connectors are properly connected
Connectors are not properly connected
| *1 | Seat Position Airbag Sensor |
| *2 | Airbag Sensor Assembly |
Disconnect the connectors from the airbag sensor assembly and seat position airbag sensor.
Check that the connectors (on the airbag sensor assembly side and seat position airbag sensor side) are not damaged.
| Proceed to |
|---|
| Connectors are not deformed or damaged |
| Connectors are deformed or damaged |
Connectors are not deformed or damaged
Connectors are deformed or damaged
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| *1 | Seat Position Airbag Sensor | *2 | Airbag Sensor Assembly |
| *3 | Connector E | *4 | Connector B |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Seat Position Airbag Sensor) |
*b | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 - Body ground | Ignition switch ON | Below 1 V |
| 2 - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 24 (LSP-) and 16 (LSP+) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 1 MΩ or higher |
| 1 - Body ground | Always | 1 MΩ or higher |
| 2 - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Seat Position Airbag Sensor |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the airbag sensor assembly and seat position airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1653/35 is not output |
| DTC B1653/35 is output |
Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.
DTC B1653/35 is not output
DTC B1653/35 is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the seat position airbag sensor.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL
Perform the inspection using parts from a normal vehicle if possible.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Seat Position Airbag Sensor |
| *2 | Airbag Sensor Assembly |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1653/35 is not output |
| DTC B1653/35 is output |
Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.
DTC B1653/35 is not output
DTC B1653/35 is output
Disconnect the No. 2 floor wire connector from the front seat inner belt assembly LH.
| *1 | Seat Position Airbag Sensor | *2 | Airbag Sensor Assembly |
| *3 | Front Seat Inner Belt Assembly LH | *4 | No. 2 Floor Wire |
| *5 | Connector C | *6 | Connector B |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH) |
*b | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N14-4 (LSP+) - Body ground | Ignition switch ON | Below 1 V |
| N14-3 (LSP-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 24 (LSP-) and 16 (LSP+) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N14-4 (LSP+) - N14-3 (LSP-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N14-4 (LSP+) - N14-3 (LSP-) | Always | 1 MΩ or higher |
| N14-4 (LSP+) - Body ground | Always | 1 MΩ or higher |
| N14-3 (LSP-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG