Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2013.11–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM J

1AD-FTV ENGINE CONTROL  ECD SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the ignition switch is turned to ON, the MIL should be illuminated and should turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A315992
0.208,0.146 2.021,0.385 1.813,0.24 10 false w/ Stop and Start System 0.365,1.979 2.281,2.198 1.917,0.219 10 false Engine Stop and Start ECU 0.365,1.771 0.719,1.979 0.354,0.208 10 false G87 1.531,0.813 1.969,1.042 0.438,0.229 10 false IGO2 1.635,1.24 2.073,1.469 0.438,0.229 10 false IG2 1.969,0.698 2.406,0.927 0.438,0.229 10 false 11 1.969,1.125 2.406,1.354 0.438,0.229 10 false 20 2.667,0.708 3.104,0.938 0.438,0.229 10 false 39 2.917,0.719 3.354,0.948 0.438,0.229 10 false IG+ 4.01,0.719 4.448,0.948 0.438,0.229 10 false CHK 2.865,1.5 4.781,1.719 1.917,0.219 10 false Combination Meter Assembly 2.854,1.323 3.208,1.531 0.354,0.208 10 false G16 4.396,0.719 4.833,0.948 0.438,0.229 10 false 11 5.063,0.719 5.302,0.948 0.24,0.229 10 false 12 5.333,0.719 5.573,0.948 0.24,0.229 10 false W 3.938,2.906 4.375,3.135 0.438,0.229 10 false IGN 1.51,2.896 1.948,3.125 0.438,0.229 10 false IG2 2.844,3.625 3.281,3.854 0.438,0.229 10 false IG2 2.458,4.031 4.24,4.438 1.781,0.406 10 false from Certification ECU (Smart Key ECU Assembly) 0.542,3.521 1.229,3.75 0.688,0.229 10 false FL MAIN 0.646,4.354 1.333,4.583 0.688,0.229 10 false Battery 5.823,5.052 6.51,5.281 0.688,0.229 10 false A61 5.813,5.24 6.5,5.469 0.688,0.229 10 false ECM 3.51,1.021 3.948,1.25 0.438,0.229 10 false MIL

A315993
0.125,0.177 3.948,0.375 3.823,0.198 10 false w/o Stop and Start System 0.396,1.073 1.385,1.333 0.99,0.26 10 false from IG2 Relay 1.927,1.281 2.531,1.542 0.604,0.26 10 false METER 2.74,1 2.99,1.188 0.25,0.188 10 false 39 3.021,1 3.375,1.188 0.354,0.188 10 false IG+ 4.469,1 4.896,1.188 0.427,0.188 10 false CHK 3.792,1.333 4.219,1.521 0.427,0.188 10 false MIL 4.875,1.01 5.125,1.198 0.25,0.188 10 false 11 5.75,1.01 6,1.198 0.25,0.188 10 false 12 6.01,1.01 6.26,1.198 0.25,0.188 10 false W 6.375,2.438 6.802,2.625 0.427,0.188 10 false ECM 6.021,2.438 6.448,2.625 0.427,0.188 10 false A61 3.063,2 5,2.271 1.938,0.271 10 false Combination Meter Assembly 3.052,1.802 3.656,2.063 0.604,0.26 10 false G16

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
Result Proceed to
MIL remains on A
MIL does not illuminate B




A

2.CHECK WHETHER DTC OUTPUT RECURS

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check if any DTCs have been detected. Note down any DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
No DTC detected A
Any DTCs detected B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




A

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the A118 ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-11 (CHK) or A61-12 (W) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL illuminated when the ignition switch is turned to ON.

OK:

MIL should be illuminated.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The GTS cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-11 (CHK) - A61-12(W) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR