Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) › from 2013.11
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0103549 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  C1611  ECU Malfunction  


DESCRIPTION

This DTC is stored if the television camera assembly judges that there is an internal malfunction as a result of its self check.

HINT:

The television camera assembly stores different types of information during initialization. If the television camera assembly cannot read the stored information when it is activated, the television camera assembly judges that there is an internal malfunction and stores this DTC.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1611 ECU Malfunction
·

EEPROM Status (Initial read)

·

ASIC Output Status


·

Parking assist monitor system initialization (not initialized television camera assembly)

·

Back camera setting (initialized television camera assembly)

·

Steering Angle setting (initialized television camera assembly)

·

Television camera assembly



CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

See pageAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>CALIBRATION


PROCEDURE

1.READ VALUE USING GTS (TELEVISION CAMERA ASSEMBLY STATUS)
a.

Use the Data List to check if the television camera assembly status is functioning properly.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>DATA LIST / ACTIVE TEST

Chassis > IPA/Parking Assist Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EEPROM Status (Initial read) Television camera assembly information OK or NG OK: Television camera assembly is normal
NG: Television camera assembly is abnormal
-
ASIC Output Status Output condition of camera display signal OK or NG OK: Output condition of camera display signal is normal
NG: Output condition of camera display signal is abnormal
If "NG" is displayed, there is a malfunction in the television camera assembly.
Chassis > IPA/Parking Assist Monitor > Data List
Tester Display
EEPROM Status (Initial read)
ASIC Output Status
50003 85 36,46
Result:
Result Proceed to
OK is displayed for both items. A
NG is displayed for EEPROM Status (Initial read).
NG is displayed for ASIC Output Status B




A

2.SETTINGS (TELEVISION CAMERA ASSEMBLY INITIALIZATION)

B

2.SETTINGS (TELEVISION CAMERA ASSEMBLY INITIALIZATION)
HINT:
·

The television camera assembly stores different types of information during initialization. If the television camera assembly cannot read the stored information when it is activated, the television camera assembly judges that there is an internal malfunction and stores this DTC.

·

If the television camera assembly cannot read the stored information when it is activated, allowing the ECU to store the information again may return the system to normal.



a.

Use the transition of diagnosis screens (note which transition pattern occurs) to confirm if the television camera assembly was able to properly store the information from initialization.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>DIAGNOSIS SYSTEM

HINT:

The procedure to make the television camera assembly store the vehicle information differs when the television camera assembly has stored the information (initialized) and when the information has not been stored (not initialized).



b.

Perform the following procedure depending on the memory conditions to register the vehicle information into the television camera assembly.

Condition Procedure
Not initialized Television camera assembly initialization
(Click here)
Initialized
·

Back camera setting

(Click here)


·

Steering angle setting (Diagnosis system)

(Click here)



Result:
Result
NEXT




NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>DTC CHECK / CLEAR

Chassis > IPA/Parking Assist Monitor > Clear DTCs
50002 85

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>DTC CHECK / CLEAR

Chassis > IPA/Parking Assist Monitor > Trouble Codes
50001 85
Result:
Proceed to
No DTC is output
DTC C1611 is output


HINT:
·

If DTC C1611 is output, perform the procedure to allow the television camera assembly to store the vehicle information again.

·

If DTC C1611 is still output after performing the procedure to make the television camera assembly store the vehicle information 3 times, replace the television camera assembly.

·

If DTC C1611 is output frequently, replace the television camera assembly even though the DTC is not output when rechecking for DTCs.





No DTC is output

END (SETTINGS ARE DEFECTIVE)

DTC C1611 is output