Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2013.11–2015.04
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047058 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The blind spot monitor sensor RH receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: except Manual Transaxle

*2: for Manual Transaxle


WIRING DIAGRAM

E271194E07
5.708,1.354 6.323,1.552 0.615,0.198 10 false T1 5.719,1.552 7,1.927 1.281,0.375 10 false Blind Spot Monitor Sensor RH 3.208,2.281 3.365,2.479 0.156,0.198 10 false 1 4.427,0.677 4.583,0.875 0.156,0.198 10 false 1 5.823,0.76 6.281,0.958 0.458,0.198 10 false SPR 5.615,0.677 5.771,0.875 0.156,0.198 10 false 8 4.427,2.281 4.583,2.479 0.156,0.198 10 false 2 3.219,0.677 3.375,0.875 0.156,0.198 10 false 2 2.052,1 2.823,1.198 0.771,0.198 10 false GAUGE 0.229,0.781 1.615,0.99 1.385,0.208 10 false from IG1 NO.2 Relay 2.906,1.219 3.365,1.417 0.458,0.198 10 false B35 2.896,1.385 5.042,1.604 2.146,0.219 10 false Back-up Light Switch Assembly*1 2.708,2.781 3.167,2.979 0.458,0.198 10 false B36 2.708,2.99 5.281,3.24 2.573,0.25 10 false Park/Neutral Position Switch Assembly*2 4.156,2.396 4.469,2.594 0.313,0.198 10 false RL 3.417,2.406 3.729,2.604 0.313,0.198 10 false RB 0.135,2.99 1.781,3.219 1.646,0.229 10 false *1: for Manual Transaxle 0.135,3.365 2.073,3.594 1.938,0.229 10 false *2: except Manual Transaxle

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE TYPE (DISPLAY CHECK MODE)
a.

Cehck the vehicle type.


Result:
Proceed to
except Manual Transaxle
for Manual Transaxle



except Manual Transaxle

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

for Manual Transaxle

4.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BLIND SPOT MONITOR SENSOR RH AND BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BLIND SPOT MONITOR SENSOR RH AND BATTERY)
a.

Disconnect the B36 park/neutral position switch assembly connector.


b.

Disconnect the T1 blind spot monitor sensor RH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B36-1 (RB) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-2 (RL) - T1-8 (SPR) Always Below 1 Ω
B36-2 (RL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY

OK

5.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY AND BATTERY)

NG

5.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY AND BATTERY)
a.

Disconnect the B35 back-up light switch assembly connector.


b.

Disconnect the T1 blind spot monitor sensor RH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B35-2 - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B35-1 - T1-8 (SPR) Always Below 1 Ω
B35-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR