Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › 2013.11–2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0048746 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  C1AA7  Skid Control Buzzer Circuit  


DESCRIPTION

The lane departure warning camera sends a buzzer request signal to the skid control buzzer assembly to sound the buzzer. When the lane departure warning camera detects a malfunction in the skid control buzzer circuit, the lane departure warning camera stores DTC C1AA7.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA7 Skid Control Buzzer Circuit
Both of the following conditions are met:
·

Skid control buzzer assembly on malfunction is detected for 240 ms or more.

·

Skid control buzzer assembly off malfunction is detected for 5 seconds or more.


·

Harness or connector

·

Skid control buzzer assembly

·

Lane departure warning camera



WIRING DIAGRAM

E256371E05
0.344,0.917 1.25,1.365 0.906,0.448 10 from IG1 NO.1 Relay 2.073,1.094 3.01,1.406 0.938,0.313 10 ECU-IG1 NO.2 5.438,0.917 5.885,1.083 0.448,0.167 10 BZ 5.229,0.771 5.427,0.927 0.198,0.156 10 8 5.281,1.729 5.583,1.917 0.302,0.188 10 Q13 5.292,1.885 6.833,2.281 1.542,0.396 10 Lane Departure Warning Camera 3.552,0.917 3.833,1.083 0.281,0.167 10 IG1 3.354,0.771 3.552,0.927 0.198,0.156 10 2 4.188,0.917 4.417,1.083 0.229,0.167 10 BZ 4.469,0.76 4.667,0.917 0.198,0.156 10 1 3.365,1.333 3.667,1.521 0.302,0.188 10 G74 3.365,1.5 4.667,2 1.302,0.5 10 Skid Control Buzzer Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When the lane departure warning camera is replaced with a new one, adjustment of the lane departure warning camera beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - LANE DEPARTURE WARNING CAMERA AND BATTERY)
a.

Disconnect the G74 skid control buzzer assembly connector.


b.

Disconnect the Q13 lane departure warning camera connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G74-2 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G74-1 (BZ) - Q13-8 (BZ) Always Below 1 Ω
G74-1 (BZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT SKID CONTROL BUZZER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR