Home › Power Source / Network › 3ZR-FAE BATTERY / CHARGING › CHARGING SYSTEM › from 2015.04
RM3090E _57 Power Source / Network _008394 3ZR-FAE BATTERY / CHARGING _0046852 CHARGING SYSTEM C

3ZR-FAE BATTERY / CHARGING  CHARGING SYSTEM  P058A  Battery Monitor Module Performance  


DESCRIPTION

The battery state sensor assembly detects the voltage, current and temperature of the battery. The charging condition is calculated from the voltage and current and output to the ECM. The ECM sends an instruction to generate voltage to the generator assembly based on that signal. Also, the battery temperature is calculated from the change in the resistance value of the thermistor built into the battery state sensor assembly and output to the ECM. The ECM reduces the charging current when the battery is hot and protects the battery based on this signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P058A Battery Monitor Module Performance Diagnosis condition: Ignition switch to ON
Malfunction status:
·

Current value is 999.939 A or higher or -1000 A or less for 3.2 seconds or more.

·

Difference between maximum and minimum current value is 0.0305 A or less for 100 seconds or more.

·

Current detection circuit malfunction condition is received.

·

Battery temperature is 105°C (221°F) or higher or -40°C (-40°F) or lower for 3.2 seconds or more.

·

Temperature detection circuit malfunction condition is received.

·

Voltage value remains at 15.98 V or higher or 6.0 V or less for 3.2 seconds or more.

·

Voltage detection circuit malfunction condition is received.

·

Battery state sensor assembly internal memory write malfunction (battery identification information) occurs.


Other: 1 trip
·

Battery state sensor assembly installation condition malfunction

·

Battery state sensor assembly

·

Wire harness or connector

·

Battery


Not displayed DTC stored

WIRING DIAGRAM

A331074E05
5.844,2.885 6.406,3.219 0.563,0.333 10 false ECM 5.531,2.875 5.99,3.073 0.458,0.198 10 false B93 5.5,0.635 5.958,0.833 0.458,0.198 10 false LIN 5.229,0.458 5.688,0.656 0.458,0.198 10 false 61 4.083,0.646 4.542,0.844 0.458,0.198 10 false LIN 4.427,0.448 4.885,0.646 0.458,0.198 10 false 2 3,0.646 3.458,0.844 0.458,0.198 10 false +B 2.719,0.479 3.177,0.677 0.458,0.198 10 false 1 1.396,0.833 2.25,1.188 0.854,0.354 10 false ALT-S/ICS 0.948,2.292 1.802,2.646 0.854,0.354 10 false Battery 2.927,1.198 5.146,1.552 2.219,0.354 10 false Battery State Sensor Assembly 2.615,1.208 3.073,1.406 0.458,0.198 10 false A75 0.771,3.271 2.802,3.573 2.031,0.302 10 false : LIN Communication Line 0.771,1.344 1.625,1.698 0.854,0.354 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When P162B (Lost Communication with Battery Monitor Module) is output at the same time, perform the inspection for P162B (Lost Communication with Battery Monitor Module) first.

Click herePower Source / Network>3ZR-FAE BATTERY / CHARGING>CHARGING SYSTEM>P162B



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION
a.

Check the installation condition of the battery state sensor assembly.

Click herePower Source / Network>3ZR-FAE BATTERY / CHARGING>BATTERY CURRENT SENSOR>INSTALLATION


Result:
Proceed to
OK
NG



OK

2.CHECK CHARGING SYSTEM

NG

INSTALL BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK CHARGING SYSTEM

Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
A331105C19
1.521,0.135 1.927,0.375 0.406,0.24 0.667,1.667 0.667,1.5 0.667,1.5 1.542,1.167 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 0.594,1.708 1.031,1.927 0.438,0.219 10 false +B 1.604,0.177 2.063,0.375 0.458,0.198 10 false A75
*a Front view of wire harness connector
(to Battery State Sensor Assembly)


Disconnect the A75 battery state sensor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A75-1 (+B) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR