Home › Power Source / Network › 3ZR-FAE BATTERY / CHARGING › CHARGING SYSTEM › from 2015.04
RM3090E _57 Power Source / Network _008394 3ZR-FAE BATTERY / CHARGING _0046852 CHARGING SYSTEM C

3ZR-FAE BATTERY / CHARGING  CHARGING SYSTEM  P162B  Lost Communication with Battery Monitor Module  


DESCRIPTION

The ECM and battery state sensor assembly each detect reception malfunctions. A battery state sensor assembly reception malfunction detected by the battery state sensor assembly is sent to the ECM via LIN communication. If there is a malfunction in either the ECM or battery state sensor assembly, the ECM determines that there is a LIN communication malfunction and outputs a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P162B Lost Communication with Battery Monitor Module Diagnosis condition: Ignition switch to ON
When the ECM cannot receive LIN communication, the battery state sensor assembly cannot receive LIN communication for approximately 33 seconds or more.
Other: 1 trip
·

Battery state sensor assembly

·

ECM

·

Wire harness or connector

·

Battery


Not displayed DTC stored

WIRING DIAGRAM

Refer to DTC P161A (Lost Communication with Alternator).

Click herePower Source / Network>3ZR-FAE BATTERY / CHARGING>CHARGING SYSTEM>P161A

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION
a.

Check the installation condition of the battery state sensor assembly.

Click herePower Source / Network>3ZR-FAE BATTERY / CHARGING>BATTERY CURRENT SENSOR>INSTALLATION


Result:
Proceed to
OK
NG



OK

2.CHECK CHARGING SYSTEM

NG

INSTALL BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK CHARGING SYSTEM

Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY STATE SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY STATE SENSOR ASSEMBLY)
a.

Disconnect the B93 ECM connector.


b.

Disconnect the A75 battery state sensor assembly connector.


c.

Disconnect the B90 generator assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B93-61 (LIN) - A75-2 (LIN) Always Below 1 Ω
B93-61 (LIN) or A75-2 (LIN) - Body ground Ignition switch off
(while LIN communication is stopped)
10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
A331105C19
1.521,0.135 1.927,0.375 0.406,0.24 0.667,1.667 0.667,1.5 0.667,1.5 1.542,1.167 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 0.594,1.708 1.031,1.927 0.438,0.219 10 false +B 1.604,0.177 2.063,0.375 0.458,0.198 10 false A75
*a Front view of wire harness connector
(to Battery State Sensor Assembly)


Disconnect the A75 battery state sensor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A75-1 (+B) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

5.READ OUTPUT DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ OUTPUT DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait at least 30 seconds.


f.

Start the engine and wait 17 minutes or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P162B is output A
P161A and P162B are output B
No DTC is output C



A

B

C