The fuel trim is related to the feedback compensation value, not to the basic injection duration. The fuel trim consists of both the short-term and long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0171 | System Too Lean (Bank 1) | With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic). | ·
Intake system ·
Fuel injector assembly blockage ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Fuel pressure ·
Gas leak from exhaust system ·
Open or short in air fuel ratio sensor (sensor 1) circuit ·
Air fuel ratio sensor (sensor 1) ·
PCV valve and hose ·
PCV hose connections ·
ECM ·
Wire harness or connector |
Comes on | DTC stored |
| P0172 | System Too Rich (Bank 1) | With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic). | ·
Fuel injector assembly leak or blockage ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Ignition system ·
Fuel pressure ·
Gas leak from exhaust system ·
Open or short in air fuel ratio sensor (sensor 1) circuit ·
Air fuel ratio sensor (sensor 1) ·
ECM ·
Wire harness or connector |
Comes on | DTC stored |
When DTC P0171 is stored, the actual air fuel ratio is on the lean side. When DTC P0172 is stored, the actual air fuel ratio is on the rich side.
If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P0171 may be stored. The MIL is then illuminated.
When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is higher than 75°C [167°F]), the system is functioning normally.
Under closed loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the fuel injection volumes estimated by the ECM also affect the average fuel trim learned value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learned value of the air fuel ratio). If the average fuel trim learned value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and stores a DTC.
Example:
The average fuel trim learned value is more than +48% or less than -35%, the ECM interprets this as a fuel system malfunction.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on. [A]
Start the engine and warm it up (until the engine coolant temperature 75°C (167°F) or higher) with all the accessories switched off. [B]
With the engine warmed up, idle the engine for 2 minutes or more. [C]
Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
Refer to DTC P0031 (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>P0031).
Refer to DTC P0102 (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>P0102).
Inspect the fuses for circuits related to this system before performing the following procedure.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0171 or P0172 is output | A |
| DTC P0171 or P0172 and other DTCs are output | B |
If any DTCs other than P0171 or P0172 are output, troubleshoot those DTCs first.
A
B
Check the PCV hose connections.
PCV valve and hose are connected correctly and are not damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leaks (Click here Engine / Hybrid System>3ZR-FAE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leaks in intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.
| Active Test Display |
|---|
| Control the Injection Volume for A/F Sensor |
| Data List Display |
|---|
| AFS Voltage B1S1 |
| O2S B1S2 |
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the 12.5% or -12.5% button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| GTS Display (Sensor) | Injection Volume | Status | Voltage |
|---|---|---|---|
| AFS Voltage B1S1
(Air fuel ratio) |
12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2
(Heated oxygen) |
12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status AFS Voltage B1S1 | Status O2S B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Suspected Trouble Area | Proceed to |
|---|---|---|---|---|
| Lean/Rich | Lean/Rich | Normal | - | A |
| Lean | Lean | Actual air fuel ratio lean | ·
PCV valve and hose ·
PCV hose connections ·
Fuel injector assembly blockage ·
Gas leak from exhaust system ·
Intake system ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor |
|
| Rich | Rich | Actual air fuel ratio rich | ·
Fuel injector assembly leak or blockage ·
Gas leak from exhaust system ·
Ignition system ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor |
|
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | Air fuel ratio sensor | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | Air fuel ratio sensor |
Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.
Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.
Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.
Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2] (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
Read the Data List twice, when the engine is both cold and warmed up.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.
| Tester Display |
|---|
| Engine Speed |
| MAF |
| Coolant Temp |
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| MAF | Shift lever position: N
A/C: Off Engine Speed: 3000 rpm |
Between 6.5 gm/sec and 10.5 gm/sec |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel pressure (Click here Engine / Hybrid System>3ZR-FAE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for exhaust gas leaks.
No gas leaks.
Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a spark test (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
If the result of the spark test is normal, proceed to the next step.
If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count (to Cylinder #4 Misfire Count).
Perform "Inspection After Repair" after repairing or replacing the ignition system (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| NEXT |
NEXT
Check the injection and volume.
Refer to the fuel injector assembly inspection procedure (Click here Engine / Hybrid System>3ZR-FAE FUEL>FUEL INJECTOR>INSPECTION).
If the fuel injector assemblies malfunction, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count (to Cylinder #4 Misfire Count).
Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the air fuel ratio sensor (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>AIR FUEL RATIO SENSOR>INSPECTION).
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Air Fuel Ratio Sensor) |
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B7-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B7-1 (HA1A) - B93-27 (HA1A) | Always | Below 1 Ω |
| B7-1 (HA1A) or B93-27 (HA1A) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air fuel ratio sensor (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0171 or P0172 is output | A |
| DTC is not output | B |
A
B
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
Repair any problems.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0171 or P0172 is output | A |
| DTC is not output | B |
A
B
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B1-5 (VG) - B93-137 (VG) | Always | Below 1 Ω |
| B1-4 (E2G) - B93-104 (E2G) | Always | Below 1 Ω |
| B1-5 (VG) or B93-137 (VG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter sub-assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).
If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0171 or P0172 is output | B |
A
B