Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P007C  Charge Air Cooler Temperature Sensor Circuit Low Bank 1  P007D  Charge Air Cooler Temperature Sensor Circuit High Bank 1  


DESCRIPTION

The intake air temperature sensor is located on the charge-air pipe between the intercooler assembly and the throttle valve. The intake air temperature sensor detects the temperature of the intake air compressed by the turbocharger and cooled by the intercooler assembly.

A temperature-dependent electrical resistor is used for temperature sensing. The circuit contains a voltage divider where the resistance can be measured depending on the temperature. A temperature is converted using a characteristic curve specific to the sensor. An NTC resistor (NTC) is installed in the intake air temperature sensor, whose resistance value drops when the temperature increases. The resistance changes between 76 kΩ and 88 Ω depending on the temperature, which corresponds to a temperature between -40°C (-40°F) and 120°C (248°F).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P007C Charge Air Cooler Temperature Sensor Circuit Low Bank 1 Intake air temperature sensor output voltage is 0.2 V or less for 0.6 seconds.
(3 trip detection logic)
·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor

·

ECM


Comes on DTC stored
P007D Charge Air Cooler Temperature Sensor Circuit High Bank 1 Intake air temperature sensor output voltage is 4.95 V or more for 0.6 seconds.
(3 trip detection logic)
·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P007C
P007D
Intake Air Temp (Turbo)

WIRING DIAGRAM

A355438E18
2.063,0.646 2.677,0.844 0.615,0.198 10 false THA 2.156,1.26 2.771,1.458 0.615,0.198 10 false E2 2.458,0.635 3.073,0.833 0.615,0.198 10 false 1 2.469,1.25 3.083,1.448 0.615,0.198 10 false 2 0.552,1.969 1.167,2.167 0.615,0.198 10 false B115 0.552,2.125 4.052,2.417 3.5,0.292 10 false Intake Air Temperature Sensor 5.271,0.635 5.885,0.833 0.615,0.198 10 false 79 5.281,1.271 5.896,1.469 0.615,0.198 10 false 89 5.552,0.635 6.167,0.833 0.615,0.198 10 false THIA 5.552,1.271 6.167,1.469 0.615,0.198 10 false ETHI 6.177,0.542 6.792,0.74 0.615,0.198 10 false R 6.219,0.156 6.833,0.354 0.615,0.198 10 false 5 V 5.979,2.313 6.594,2.51 0.615,0.198 10 false B112 5.99,2.469 6.604,2.667 0.615,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMP (TURBO))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Temp (Turbo)
50003 371 54

d.

Read the value.

OK:

Same as actual intake air temperature.


Result:
Result Proceed to
-40°C (-40°F) A
120°C (248°F) or more B
Same as actual intake air temperature C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F) or less.

·

If there is a short circuit, the GTS indicates 120°C (248°F) or more.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the intake air temperature sensor connector.


b.

Connect terminals B115-1 (THA) and B115-2 (E2) of the intake air temperature sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Temp (Turbo)
50003 371 54
Standard value:

120°C (248°F) or more



Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR
a.

Replace the intake air temperature sensor.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B115-1 (THA) - B112-79 (THIA) Always Below 1 Ω
B115-2 (E2) - B112-89 (ETHI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the intake air temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Temp (Turbo)
50003 371 54
Standard value:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

7.REPLACE INTAKE AIR TEMPERATURE SENSOR

NG

8.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
7.REPLACE INTAKE AIR TEMPERATURE SENSOR
a.

Replace the intake air temperature sensor.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B115-1 (THA) or B112-79 (THIA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END