Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0100  Mass or Volume Air Flow Sensor "A" Circuit  


DESCRIPTION

When the engine is running and the supply voltage to the ECM is outside the threshold, the ECM determines that the supply voltage to the mass air flow meter sub-assembly has decreased.

When the supply voltage to the mass air flow meter sub-assembly has decreased, this DTC differentiates when there is a malfunction with the mass air flow meter sub-assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0100 Mass or Volume Air Flow Sensor "A" Circuit Either condition is met (3 trip detection logic):
·

Supply voltage to ECM while engine is running is less than 7 V for 1 second.

·

Supply voltage to ECM while engine is running is more than 17 V for 1 second.


·

Open or short in power source circuit

·

Battery

·

EFI MAIN NO. 1 relay

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A372439E02
4.125,1.156 7.135,1.427 3.01,0.271 10 false Certification ECU (Smart Key ECU Assembly)*1 1.25,1.198 3.188,1.448 1.938,0.25 10 false Ignition Switch Assembly*2 0.719,0.896 1.177,1.094 0.458,0.198 10 false AM2 1.24,1.042 1.698,1.24 0.458,0.198 10 false G4 4.125,1.01 4.583,1.208 0.458,0.198 10 false G82 5.396,0.74 5.917,0.938 0.521,0.198 10 false IG2D 1.615,0.646 2.073,0.844 0.458,0.198 10 false AM2 2.198,0.656 2.656,0.854 0.458,0.198 10 false IG2 2.5,0.646 2.833,0.854 0.333,0.208 10 false 3 1.458,0.646 1.667,0.854 0.208,0.208 10 false 4 2.625,1.667 2.833,1.875 0.208,0.208 10 false 3 3.417,1.656 3.625,1.865 0.208,0.208 10 false 5 3.417,2.031 3.625,2.24 0.208,0.208 10 false 1 2.635,2.042 2.844,2.25 0.208,0.208 10 false 2 1.927,1.906 2.385,2.104 0.458,0.198 10 false IG2 1.177,4.052 2.417,4.292 1.24,0.24 10 false EFI MAIN NO. 1 3.094,4.563 4.333,4.802 1.24,0.24 10 false EFI MAIN NO. 1 3.146,4.125 3.354,4.333 0.208,0.208 10 false 2 3.938,4.115 4.146,4.323 0.208,0.208 10 false 1 3.156,3.729 3.365,3.938 0.208,0.208 10 false 5 3.948,3.729 4.156,3.938 0.208,0.208 10 false 3 4.406,2.688 5.646,2.927 1.24,0.24 10 false EFI MAIN NO. 2 4.333,4.01 5.573,4.25 1.24,0.24 10 false EFI NO. 3 6.198,6.25 6.656,6.448 0.458,0.198 10 false A62 6.188,6.417 6.646,6.615 0.458,0.198 10 false ECM 1.917,5.604 3.958,5.875 2.042,0.271 10 false *1: w/ Entry and Start System 1.927,5.979 4.063,6.24 2.135,0.26 10 false *2: w/o Entry and Start System 2.948,2.479 3.406,2.677 0.458,0.198 10 false IG2 4.396,1.906 4.854,2.104 0.458,0.198 10 false IGN 5.823,1.75 6.438,1.948 0.615,0.198 10 false IGSW 5.823,2.51 6.438,2.708 0.615,0.198 10 false BATT 5.813,3 6.427,3.198 0.615,0.198 10 false +B3 5.823,3.417 6.438,3.615 0.615,0.198 10 false +B2 5.823,3.823 6.438,4.021 0.615,0.198 10 false +B 5.823,4.198 6.438,4.396 0.615,0.198 10 false MREL 5.823,4.646 6.438,4.844 0.615,0.198 10 false E1 5.833,5.042 6.448,5.24 0.615,0.198 10 false E2 5.833,5.438 6.448,5.635 0.615,0.198 10 false E3 5.833,5.865 6.448,6.063 0.615,0.198 10 false E4 5.573,2.427 5.885,2.625 0.313,0.198 10 false 15 5.604,2.917 5.917,3.115 0.313,0.198 10 false 1 5.542,1.646 5.854,1.844 0.313,0.198 10 false 37 5.573,3.333 5.885,3.531 0.313,0.198 10 false 14 5.615,3.74 5.927,3.938 0.313,0.198 10 false 2 5.625,4.125 5.938,4.323 0.313,0.198 10 false 9 5.625,4.552 5.938,4.75 0.313,0.198 10 false 4 5.625,4.948 5.938,5.146 0.313,0.198 10 false 5 5.552,5.333 5.865,5.531 0.313,0.198 10 false 17 5.563,5.771 5.875,5.969 0.313,0.198 10 false 18 5.219,0.635 5.531,0.833 0.313,0.198 10 false 9 0.646,5.375 1.719,5.573 1.073,0.198 10 false Battery 0.51,4.625 1.583,4.823 1.073,0.198 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK BATTERY VOLTAGE

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR

NG

7.RECHARGE OR REPLACE BATTERY
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the negative (-) battery terminal.


b.

Disconnect the positive (+) battery terminal.


c.

Disconnect the ECM connector.


d.

Remove the EFI MAIN NO. 1 relay from the engine room and junction block.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-4 (E1) - Body ground Always Below 1 Ω
A62-5 (E2) - Body ground Always Below 1 Ω
A62-17 (E3) - Body ground Always Below 1 Ω
A62-18 (E4) - Body ground Always Below 1 Ω
A62-15 (BATT) - positive (+) battery terminal Always Below 1 Ω
A62-2 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-14 (+B2) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-1 (+B3) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-9 (MREL) - 1 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
5 (EFI MAIN NO. 1 relay holder) - positive (+) battery terminal Always Below 1 Ω
2 (EFI MAIN NO. 1 relay holder) - Body ground Always Below 1 Ω
A62-15 (BATT) or positive (+) battery terminal - Body ground Always 10 kΩ or higher
A62-2 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-14 (+B2) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-1 (+B3) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-9 (MREL) or 1 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
5 (EFI MAIN NO. 1 relay holder) or positive (+) battery terminal - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT EFI MAIN NO. 1 RELAY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT EFI MAIN NO. 1 RELAY
a.

Inspect the EFI MAIN NO. 1 relay.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPLACE EFI MAIN NO. 1 RELAY
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE EFI MAIN NO. 1 RELAY
a.

Replace the EFI MAIN NO. 1 relay.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.RECHARGE OR REPLACE BATTERY
a.

Recharge or replace the battery.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END