Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0122  Throttle/Pedal Position Sensor / Switch "A" Circuit Low  P0123  Throttle / Pedal Position Sensor/Switch "A" Circuit High  


DESCRIPTION

The ECM furnishes the 5-volt power and the ground connection for the throttle-valve actuator.

The ECM control unit opens and closes the throttle valve actuator electrically.

The exact current position of the throttle valve must be registered at all times in order to perform optimal control. This function is discharged by the throttle-valve sensor, which provides contactless monitoring of the throttle valve position within the throttle-valve actuator.

The electromotive throttle actuator is secured to the intake plenum.

A throttle valve is necessary for all diesel engines equipped with a particulate filter system. The throttle valve blocks the intake air to ensure that the necessary increased exhaust-gas temperatures required for regeneration of the particulate filter are reached.

The throttle-valve actuator closes when the ignition switch is turned off. This counteracts the tendency of the engine to vibrate during the shutdown phase. Another function is preventing the engine from overrevving.

When the ECD system detects increases in engine speed although no corresponding rises in the injection quantity have occurred, it responds by closing the throttle valve to limit engine speed.

A342520E01
1.292,0.552 1.531,0.552 1.531,0.552 1.948,1.667 false 0.698,2.469 0.375,3.323 0.375,3.323 0.635,3.323 false 5.708,1.448 5.844,1.448 5.844,1.448 5.958,1.583 false 5.208,2.094 5.333,2.198 5.333,2.198 5.49,2.198 false 0.406,0.469 1.313,0.698 0.906,0.229 10 false Throttle Valve 0.708,3.229 1.906,3.469 1.198,0.24 10 false Throttle Actuator 3.74,0.385 5.594,0.594 1.854,0.208 10 false Throttle Valve Position (%) 4.198,1.344 5.677,1.688 1.479,0.344 10 true Maximum characteristic curve 5.531,2.104 7.01,2.5 1.479,0.396 10 true Maximum characteristic curve 5,3.083 7,3.354 2,0.271 10 true Throttle Valve Opening Angle

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0122 Throttle/Pedal Position Sensor / Switch "A" Circuit Low Throttle position sensor output (VTA1) is less than 0.15 V for 0.22 seconds.
(3 trip detection logic)
·

Throttle position sensor (diesel throttle body assembly)

·

Open or short in throttle position sensor circuit

·

ECM


Does not come on DTC stored
P0123 Throttle / Pedal Position Sensor/Switch "A" Circuit High Throttle position sensor output (VTA1) is more than 4.7 V for 0.22 seconds.
(3 trip detection logic)
·

Throttle position sensor (diesel throttle body assembly)

·

Open or short in throttle position sensor circuit

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P0122
P0123
·

Target Throttle Position

·

Actual Throttle Position

·

Throttle Sensor Volt %



HINT:

Throttle position sensor output voltage "Throttle Sensor Volt %" is converted using 5 V = 100 %.


WIRING DIAGRAM

A311418E04
1.563,0.875 1.875,1.073 0.313,0.198 10 false VC 1.51,1.385 1.885,1.604 0.375,0.219 10 false VTA 1.594,1.906 1.969,2.125 0.375,0.219 10 false E2 1.583,2.427 1.958,2.646 0.375,0.219 10 false M+ 1.615,2.948 1.99,3.167 0.375,0.219 10 false M- 1.875,0.76 2.063,0.969 0.188,0.208 10 false 1 1.885,1.281 2.073,1.49 0.188,0.208 10 false 3 1.896,1.802 2.083,2.01 0.188,0.208 10 false 2 1.896,2.333 2.083,2.542 0.188,0.208 10 false 4 1.896,2.854 2.083,3.063 0.188,0.208 10 false 5 0.25,3.385 0.625,3.604 0.375,0.219 10 false o1 0.26,3.542 2.167,3.771 1.906,0.229 10 false Diesel Throttle Body Assembly 5.229,0.76 5.542,0.958 0.313,0.198 10 false 83 5.156,1.292 5.469,1.49 0.313,0.198 10 false 117 5.229,1.813 5.542,2.01 0.313,0.198 10 false 81 5.229,2.333 5.542,2.531 0.313,0.198 10 false 50 5.229,2.854 5.542,3.052 0.313,0.198 10 false 20 5.479,0.854 5.969,1.094 0.49,0.24 10 false VCTA 5.479,1.375 5.969,1.615 0.49,0.24 10 false VTA1 5.49,1.906 5.979,2.146 0.49,0.24 10 false ETA 5.49,2.417 5.979,2.656 0.49,0.24 10 false M+ 5.49,2.938 5.979,3.177 0.49,0.24 10 false M- 5.854,3.969 6.344,4.208 0.49,0.24 10 false B112 5.865,4.125 6.354,4.365 0.49,0.24 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
o1-1 (VC) - B112-83 (VCTA) Always Below 1 Ω
o1-3 (VTA) - B112-117 (VTA1) Always Below 1 Ω
o1-2 (E2) - B112-81 (ETA) Always Below 1 Ω
o1-1 (VC) or B112-83 (VCTA) - Body ground Always 10 kΩ or higher
o1-3 (VTA) or B112-117 (VTA1) - Body ground Always 10 kΩ or higher
o1-2 (E2) or B112-81 (ETA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
a.
A351163C05
0.219,1.063 0.635,1.302 0.417,0.24 1.552,1.75 1.927,1.271 false 2.531,1.74 2.208,1.26 false 0.25,0.177 0.563,0.375 0.313,0.198 10 false *a 0.354,1.094 0.667,1.292 0.313,0.198 10 false o1 1.427,1.781 1.74,1.979 0.313,0.198 10 false E2 2.49,1.76 2.802,1.958 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Diesel Throttle Body Assembly)


Disconnect the diesel throttle body assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
o1-1 (VC) - o1-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace diesel throttle body assembly.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0122 AND/OR P0123)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0122 AND/OR P0123)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P0122 and/or P0123 B




A

END

B

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END