Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0182  Fuel Temperature Sensor "A" Circuit Low  P0183  Fuel Temperature Sensor "A" Circuit High  


DESCRIPTION

The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low.

The variations of resistance are communicated to the ECM as changes of voltage.

The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.

Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change of fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump assembly and determines if there are errors.

HINT:

When the fuel temperature sensor output is outside the normal range, the ECM determines that this is a malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0182 Fuel Temperature Sensor "A" Circuit Low Fuel temperature sensor output voltage is 0.15 V or less for 0.6 seconds.
(3 trip detection logic)
·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor

·

ECM


Does not come on DTC stored
P0183 Fuel Temperature Sensor "A" Circuit High Fuel temperature sensor output voltage is 4.96 V or more for 0.6 seconds.
(3 trip detection logic)
·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P0182
P0183
Fuel Temperature

WIRING DIAGRAM

A355423E06
2.083,0.646 2.542,0.844 0.458,0.198 10 false THF 2.135,1.271 2.417,1.479 0.281,0.208 10 false E2 2.458,1.26 2.74,1.469 0.281,0.208 10 false 2 2.438,0.656 2.719,0.865 0.281,0.208 10 false 1 0.646,1.948 1.104,2.146 0.458,0.198 10 false B120 0.667,2.125 3.115,2.396 2.448,0.271 10 false Fuel Temperature Sensor 5.24,0.646 5.521,0.854 0.281,0.208 10 false 93 5.188,1.271 5.49,1.479 0.302,0.208 10 false 124 5.531,0.656 5.99,0.854 0.458,0.198 10 false THF 5.531,1.271 5.99,1.469 0.458,0.198 10 false ETHF 6.208,0.229 6.583,0.417 0.375,0.188 10 false 5 V 6.156,0.531 6.313,0.729 0.156,0.198 10 false R 5.99,2.292 6.427,2.542 0.438,0.25 10 false B112 6,2.438 6.438,2.688 0.438,0.25 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (FUEL TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Temperature
50003 371 141

d.

Read the value.

OK:

Same as actual fuel temperature.


Result:
Result Proceed to
-40°C (-40°F) A
120°C (248°F) or higher B
Same as actual fuel temperature C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 120°C (248°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the fuel temperature sensor connector.


b.

Connect terminals B120-1 (THF) and B120-2 (E2) of the fuel temperature sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Temperature
50003 371 141

f.

Read the value.

Standard value:

120°C (248°F) or higher



Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE FUEL TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor.

Click hereEngine / Hybrid System>2WW FUEL>FUEL TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B120-1 (THF) - B112-93 (THF) Always Below 1 Ω
B120-2 (E2) - B112-124 (ETHF) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the fuel temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Temperature
50003 371 141

e.

Read the value.

Standard value:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

7.REPLACE FUEL TEMPERATURE SENSOR

NG

8.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
7.REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor.

Click hereEngine / Hybrid System>2WW FUEL>FUEL TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B120-1 (THF) or B112-93 (THF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END