| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0234 | Turbocharger / Supercharger "A" Overboost Condition | Actual turbocharger pressure is at higher than target pressure threshold for 5 seconds.
(3 trip detection logic) |
·
Intake system air leak ·
Turbocharger sub-assembly ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0234 | ·
Target Booster Pressure ·
MAP |
When replacing the ECM, the ECM needs registration and initialization.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION
When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Start the engine.
Check air duct between intake silencer, mass air flow meter sub-assembly and turbocharger for leaks.
Check air duct between turbocharger and intake manifold for leaks.
Oily patches are signs of leaks.
Check whether sealing rings on charge air hoses are rolled back or missing.
No leakage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Turbo Charger.
| Tester Display |
|---|
| Actuator Test of Turbo Charger |
Set the control value to 5%. The variable nozzle vane turbocharger must operate within 1 second. Valve travel when adjusted is approximately 15 mm.
Wait for 2 seconds and set the control value to 95%. The variable nozzle vane turbocharger must operate within 1 second. Valve travel when adjusted is approximately 15 mm.
Wait for 2 seconds and stop the operation using the variable nozzle vane turbocharger Active Test.
Operates smoothly when above procedure is performed.
Check the movement of the variable turbine (stiffness, interference with other parts, etc.).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC output | A |
| DTC P0234 | B |
A
B
Replace the turbocharger sub-assembly.
Click hereEngine / Hybrid System>2WW INTAKE / EXHAUST>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC output | A |
| DTC P0234 | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the malfunctioning parts of the intake system.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT