| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0299 | Turbocharger / Supercharger "A" Underboost Condition | Actual turbocharger pressure is at lower than target pressure threshold for 7 seconds.
(3 trip detection logic) |
·
Leaks from air intake system ·
Exhaust gas leak before turbocharger sub-assembly ·
Diesel throttle body assembly ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0299 | ·
Target Booster Pressure ·
MAP |
When replacing the ECM, the ECM needs registration and initialization.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION
When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Start the engine.
Check air duct between intake silencer, mass air flow meter sub-assembly and turbocharger for leaks.
Check air duct between turbocharger and intake manifold for leaks.
Oily patches are signs of leaks.
Check whether sealing rings on charge air hoses are rolled back or missing.
No leakage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for exhaust gas leak before the turbocharger sub-assembly.
No exhaust gas leak.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Throttle Valve / Data List / Throttle Valve Actuator Position.
| Active Test Display |
|---|
| Actuator Test of Throttle Valve |
| Data List Display |
|---|
| Throttle Valve Actuator Position |
Perform the following steps 1 to 4.
Step 1
Perform Active Test of throttle valve with control value of 5% (opening ratio in %).
Monitor the difference of the control value and Throttle Valve Actuator Position value (0 +/-3%). Throttle valve must operate within 1 second.
Step 2
Wait for 2 seconds or more.
Step 3
Perform Active Test of throttle valve with control value of 91% (opening ratio in %).
Monitor the difference of the control value and Throttle Valve Actuator Position value (0 +/-3%). Throttle valve must operate within 1 second.
Step 4
Wait for 2 seconds or more.
Perform the above steps 1 to 4 and check that the part operates as specified.
Part operates as specified.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the diesel throttle body assembly.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC output | A |
| DTC P0299 | B |
A
B
Repair or replace the malfunctioning parts of the exhaust system.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the malfunctioning parts of the intake system.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT