Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0336  Crankshaft Position Sensor "A" Circuit Range / Performance  


DESCRIPTION

The crankshaft position sensor is installed to the gearbox case.

The crankshaft position sensor records the position of the crankshaft with the aid of a sensor wheel screwed to the flywheel.

The ECM uses the signals to calculate the duration as well as the length of one crankshaft revolution.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit No crankshaft position sensor signal to ECM while cranking.
(3 trip detection logic)
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Does not come on DTC stored
P0336 Crankshaft Position Sensor "A" Circuit Range / Performance Wrong pattern of signal from sensor is detected.
(3 trip detection logic)
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A351169E05
6.031,0.323 6.479,0.5 0.448,0.177 10 false VCNE 6.042,0.74 6.49,0.917 0.448,0.177 10 false NE+ 6.031,1.135 6.479,1.313 0.448,0.177 10 false NE- 6.031,2.229 6.479,2.406 0.448,0.177 10 false G+ 6.031,2.844 6.479,3.021 0.448,0.177 10 false G- 6.042,4.615 6.49,4.792 0.448,0.177 10 false MREL 6.271,5.25 6.719,5.427 0.448,0.177 10 false ECM 5.677,4.604 6.125,4.781 0.448,0.177 10 false A62 5.635,0.302 6.083,0.479 0.448,0.177 10 false B112 5.635,0.74 6.083,0.917 0.448,0.177 10 false B112 5.635,1.125 6.083,1.302 0.448,0.177 10 false B112 5.635,2.229 6.083,2.406 0.448,0.177 10 false B112 5.635,2.833 6.083,3.01 0.448,0.177 10 false B112 5.75,4.396 5.948,4.583 0.198,0.188 10 false 9 5.667,0.125 5.99,0.313 0.323,0.188 10 false 122 5.667,0.552 5.99,0.74 0.323,0.188 10 false 121 5.708,0.938 6.031,1.125 0.323,0.188 10 false 90 5.708,2.021 6.031,2.208 0.323,0.188 10 false 68 5.667,2.646 5.99,2.833 0.323,0.188 10 false 115 2.844,0.208 3.104,0.438 0.26,0.229 10 false 1 2.854,0.646 3.115,0.875 0.26,0.229 10 false 2 2.854,1.042 3.115,1.271 0.26,0.229 10 false 3 2.542,0.323 2.865,0.542 0.323,0.219 10 false VG 2.563,0.74 2.885,0.958 0.323,0.219 10 false NE 2.51,1.115 2.958,1.292 0.448,0.177 10 false NE- 5.208,2.125 5.469,2.354 0.26,0.229 10 false 1 5.219,2.74 5.479,2.969 0.26,0.229 10 false 2 3.833,2.135 4.094,2.365 0.26,0.229 10 false 3 4.01,2.229 4.333,2.448 0.323,0.219 10 false VG 4.927,2.219 5.25,2.438 0.323,0.219 10 false G1 2.896,2.385 3.646,2.604 0.75,0.219 10 false EFI NO. 1 4.948,2.844 5.396,3.021 0.448,0.177 10 false G- 3.781,3.229 4.188,3.417 0.406,0.188 10 false B123 3.781,3.385 5.417,3.677 1.635,0.292 10 false Camshaft Position Sensor 2.479,2.135 2.74,2.365 0.26,0.229 10 false 3 1.698,2.417 1.958,2.646 0.26,0.229 10 false 2 2.479,2.406 2.74,2.635 0.26,0.229 10 false 1 1.708,2.135 1.969,2.365 0.26,0.229 10 false 5 1.844,2.844 2.458,3.26 0.615,0.417 10 false EFI MAIN NO. 1 0.719,2.396 1.344,2.833 0.625,0.438 10 false EFI MAIN NO. 1 0.677,3.906 1.427,4.125 0.75,0.219 10 false FL MAIN 0.854,4.917 1.604,5.135 0.75,0.219 10 false Battery 1.385,1.396 1.813,1.656 0.427,0.26 10 false B114 1.375,1.563 3.26,1.854 1.885,0.292 10 false Crankshaft Position Sensor

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Check the value on the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine and turn the GTS on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


·

The engine speed can be confirmed in the Data List using the GTS. If there are no NE signals from the crankshaft position sensor despite the engine running, the engine speed will be indicated as zero. If the voltage output of the crankshaft position sensor is insufficient, the engine speed will be indicated as lower than the actual engine speed.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B114-2 (NE) - B112-121 (NE+) Always Below 1 Ω
B114-3 (NE-) - B112-90 (NE-) Always Below 1 Ω
B114-1 (VG) - B112-122 (VCNE) Always Below 1 Ω
B114-2 (NE) or B112-121 (NE+) - Body ground Always 10 kΩ or higher
B114-3 (NE-) or B112-90 (NE-) - Body ground Always 10 kΩ or higher
B114-1 (VG) or B112-122 (VCNE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A351158C21
0.302,1.146 0.75,1.365 0.448,0.219 0.948,1.792 1.354,1.281 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.365,1.177 0.833,1.375 0.469,0.198 10 false B114 0.802,1.833 1.271,2.031 0.469,0.198 10 false VG
*a Front view of wire harness connector
(to Crankshaft Position Sensor)


a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B114-1 (VG) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

7.REPLACE ECM
3.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.

Check the crankshaft position sensor installation.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.REPLACE CRANKSHAFT POSITION SENSOR

NG

6.SECURELY REINSTALL SENSOR
4.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 AND/OR P0336)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 AND/OR P0336)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P0335 and/or P0336 B




A

END

B

7.REPLACE ECM
6.SECURELY REINSTALL SENSOR
a.

Securely reinstall crankshaft position sensor.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END