Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0340  Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor  P0344  Camshaft Position Sensor "A" Circuit Intermittent Bank 1 or Single Sensor  


DESCRIPTION

The camshaft position sensor is installed on the cylinder head cover. The camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, the tooth on the camshaft passes through the camshaft position sensor. The generated voltage in the sensor acts as a signal. The ECM locates each cylinder position based on the combination of this signal and crankshaft position sensor output.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor No camshaft position sensor signal to ECM.
(3 trip detection logic)
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft

·

ECM


Does not come on DTC stored
P0344 Camshaft Position Sensor "A" Circuit Intermittent Bank 1 or Single Sensor Wrong pattern of signal from sensor is detected.
(3 trip detection logic)
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A351169E05
6.031,0.323 6.479,0.5 0.448,0.177 10 false VCNE 6.042,0.74 6.49,0.917 0.448,0.177 10 false NE+ 6.031,1.135 6.479,1.313 0.448,0.177 10 false NE- 6.031,2.229 6.479,2.406 0.448,0.177 10 false G+ 6.031,2.844 6.479,3.021 0.448,0.177 10 false G- 6.042,4.615 6.49,4.792 0.448,0.177 10 false MREL 6.271,5.25 6.719,5.427 0.448,0.177 10 false ECM 5.677,4.604 6.125,4.781 0.448,0.177 10 false A62 5.635,0.302 6.083,0.479 0.448,0.177 10 false B112 5.635,0.74 6.083,0.917 0.448,0.177 10 false B112 5.635,1.125 6.083,1.302 0.448,0.177 10 false B112 5.635,2.229 6.083,2.406 0.448,0.177 10 false B112 5.635,2.833 6.083,3.01 0.448,0.177 10 false B112 5.75,4.396 5.948,4.583 0.198,0.188 10 false 9 5.667,0.125 5.99,0.313 0.323,0.188 10 false 122 5.667,0.552 5.99,0.74 0.323,0.188 10 false 121 5.708,0.938 6.031,1.125 0.323,0.188 10 false 90 5.708,2.021 6.031,2.208 0.323,0.188 10 false 68 5.667,2.646 5.99,2.833 0.323,0.188 10 false 115 2.844,0.208 3.104,0.438 0.26,0.229 10 false 1 2.854,0.646 3.115,0.875 0.26,0.229 10 false 2 2.854,1.042 3.115,1.271 0.26,0.229 10 false 3 2.542,0.323 2.865,0.542 0.323,0.219 10 false VG 2.563,0.74 2.885,0.958 0.323,0.219 10 false NE 2.51,1.115 2.958,1.292 0.448,0.177 10 false NE- 5.208,2.125 5.469,2.354 0.26,0.229 10 false 1 5.219,2.74 5.479,2.969 0.26,0.229 10 false 2 3.833,2.135 4.094,2.365 0.26,0.229 10 false 3 4.01,2.229 4.333,2.448 0.323,0.219 10 false VG 4.927,2.219 5.25,2.438 0.323,0.219 10 false G1 2.896,2.385 3.646,2.604 0.75,0.219 10 false EFI NO. 1 4.948,2.844 5.396,3.021 0.448,0.177 10 false G- 3.781,3.229 4.188,3.417 0.406,0.188 10 false B123 3.781,3.385 5.417,3.677 1.635,0.292 10 false Camshaft Position Sensor 2.479,2.135 2.74,2.365 0.26,0.229 10 false 3 1.698,2.417 1.958,2.646 0.26,0.229 10 false 2 2.479,2.406 2.74,2.635 0.26,0.229 10 false 1 1.708,2.135 1.969,2.365 0.26,0.229 10 false 5 1.844,2.844 2.458,3.26 0.615,0.417 10 false EFI MAIN NO. 1 0.719,2.396 1.344,2.833 0.625,0.438 10 false EFI MAIN NO. 1 0.677,3.906 1.427,4.125 0.75,0.219 10 false FL MAIN 0.854,4.917 1.604,5.135 0.75,0.219 10 false Battery 1.385,1.396 1.813,1.656 0.427,0.26 10 false B114 1.375,1.563 3.26,1.854 1.885,0.292 10 false Crankshaft Position Sensor

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B123-1 (G1) - B112-68 (G+) Always Below 1 Ω
B123-2 (G-) - B112-115 (G-) Always Below 1 Ω
B123-1 (G1) or B112-68 (G+) - Body ground Always 10 kΩ or higher
B123-2 (G-) or B112-115 (G-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT POSITION SENSOR - EFI MAIN NO. 1 RELAY OR ECM POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A351158C22
0.302,1.146 0.75,1.365 0.448,0.219 2.333,1.833 2.104,1.26 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.375,1.177 0.844,1.375 0.469,0.198 10 false B123 2.24,1.865 2.708,2.063 0.469,0.198 10 false VG
*a Front view of wire harness connector
(to Camshaft Position Sensor)


a.

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B123-3 (VG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT POSITION SENSOR - EFI MAIN NO. 1 RELAY OR ECM POWER SOURCE CIRCUIT)
3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
a.

Check the camshaft position sensor installation.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT CAMSHAFT (TIMING ROTOR)

NG

9.SECURELY REINSTALL SENSOR
4.INSPECT CAMSHAFT (TIMING ROTOR)
a.

Inspect the timing rotor of the camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

5.REPLACE CAMSHAFT POSITION SENSOR

NG

8.REPLACE CAMSHAFT
5.REPLACE CAMSHAFT POSITION SENSOR

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340 AND/OR P0344)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340 AND/OR P0344)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.


Result:
Result Proceed to
No DTC output A
DTC P0340 and/or P0344 B



A

END

B

7.REPLACE ECM
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE CAMSHAFT

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.SECURELY REINSTALL SENSOR
a.

Securely reinstall camshaft position sensor.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT POSITION SENSOR - EFI MAIN NO. 1 RELAY OR ECM POWER SOURCE CIRCUIT)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END