Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P040C  Exhaust Gas Recirculation Temperature Sensor "A" Circuit Low  P040D  Exhaust Gas Recirculation Temperature Sensor "A" Circuit High  


DESCRIPTION

The EGR gas temperature sensor is located on the EGR cooler.

The EGR gas temperature sensor is required for the exact control of the exhaust gas recirculation.

A thermistor built into the sensor changes its resistance value according to the exhaust gas recirculation temperature. The lower the exhaust gas recirculation temperature, the greater the thermistor resistance value. The higher the exhaust gas recirculation temperature, the lower the thermistor resistance value.

The EGR gas temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the EGR gas temperature sensor from terminal THEC via resistor R.

The resistor R and the EGR gas temperature sensor are connected in series. When the resistance value of the EGR gas temperature sensor changes in accordance with changes in the exhaust gas recirculation gas temperature, the voltage at terminal THEC also changes.

The resistance is temperature dependent and varies between 138 kΩ and 127 Ω, which corresponds to a temperature of -50°C (-58°F) to 500°C (932°F) (See Fig. 1).

A342514E01
0.479,0.104 1.708,0.302 1.229,0.198 10 false (Fig. 1) 1.333,0.104 2.563,0.302 1.229,0.198 10 false Resistance (Ω) 5,3.365 6.229,3.563 1.229,0.198 10 false Temperature (°C)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P040C Exhaust Gas Recirculation Temperature Sensor "A" Circuit Low EGR gas temperature sensor output voltage is 0.2 V or less for 0.6 seconds.
(3 trip detection logic)
·

Open or short in EGR gas temperature sensor circuit

·

EGR gas temperature sensor

·

ECM


Comes on DTC stored
P040D Exhaust Gas Recirculation Temperature Sensor "A" Circuit High EGR gas temperature sensor output voltage is 4.98 V or more for 0.6 seconds.
(3 trip detection logic)
·

Open or short in EGR gas temperature sensor circuit

·

EGR gas temperature sensor

·

ECM


Comes on DTC stored

Related Data Lis
DTC No. Data List
P040C
P040D
Temperature Down Stream of EGR Cooler

WIRING DIAGRAM

A355438E20
1.958,0.635 2.573,0.833 0.615,0.198 10 false THEC 2.156,1.26 2.771,1.458 0.615,0.198 10 false E2 2.458,0.635 3.073,0.833 0.615,0.198 10 false 1 2.469,1.25 3.083,1.448 0.615,0.198 10 false 2 0.563,2 1.177,2.198 0.615,0.198 10 false B132 0.563,2.167 2.76,2.396 2.198,0.229 10 false EGR Gas Temperature Sensor 5.198,0.635 5.813,0.833 0.615,0.198 10 false 118 5.281,1.271 5.896,1.469 0.615,0.198 10 false 86 5.552,0.635 6.167,0.833 0.615,0.198 10 false THEC 5.552,1.271 6.167,1.469 0.615,0.198 10 false ETEC 6.177,0.542 6.792,0.74 0.615,0.198 10 false R 6.219,0.156 6.833,0.354 0.615,0.198 10 false 5 V 6.01,2.292 6.625,2.49 0.615,0.198 10 false B112 6.021,2.458 6.635,2.656 0.615,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EGR GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the EGR gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B132-1 (THEC) - B112-118 (THEC) Always Below 1 Ω
B132-2 (E2) - B112-86 (ETEC) Always Below 1 Ω
B132-1 (THEC) or B112-118 (THEC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT EGR GAS TEMPERATURE SENSOR

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT EGR GAS TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPLACE EGR GAS TEMPERATURE SENSOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE EGR GAS TEMPERATURE SENSOR
a.

Replace the EGR gas temperature sensor.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END