Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0545  Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 1  P0546  Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 1  


DESCRIPTION

The exhaust gas temperature sensors are installed before and after the NSC catalytic converter to sense the exhaust gas temperature.

A thermistor built into the sensor changes its resistance value according to the exhaust gas temperature.

The lower the exhaust gas temperature, the greater the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value.

The exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the exhaust gas temperature sensor from terminal THCI (for sensor 1) and THCO (for sensor 2) via resistor R.

The resistor R and the exhaust gas temperature sensor are connected in series. When the resistance value of the exhaust gas temperature sensor changes in accordance with changes in the exhaust gas temperature, the voltage at terminals THCI (for sensor 1) and THCO (for sensor 2) also changes.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0545 Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 1 When exhaust gas temperature sensor (for sensor 1) value falls below minimum threshold for 0.6 seconds.
(3 trip detection logic)
·

Open or short in exhaust gas temperature sensor (for sensor 1) circuit

·

Exhaust gas temperature sensor (for sensor 1)

·

ECM


Comes on DTC stored
P0546 Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 1 When exhaust gas temperature sensor (for sensor 1) value exceeds maximum threshold for 0.6 seconds.
(3 trip detection logic)
·

Open or short in exhaust gas temperature sensor (for sensor 1) circuit

·

Exhaust gas temperature sensor (for sensor 1)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0545
P0546
Exhaust Temperature B1S1

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 1) - ECM)
a.

Disconnect the exhaust gas temperature sensor (for sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B108-1 (THCI) - B112-92 (THCI) Always Below 1 Ω
B108-2 (E2) - B112-91 (ETCI) Always Below 1 Ω
B108-1 (THCI) or B112-92 (THCI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 1)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 1)
a.

Inspect the exhaust gas temperature sensor (for sensor 1).

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR(for Sensor 1)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 1)
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 1)
a.

Replace the exhaust gas temperature sensor (for sensor 1).

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR(for Sensor 1)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END