Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0607  Control Module Performance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0607 Control Module Performance Either condition is met (1 trip detection logic):
·

Decrease in ECM supply voltage resulting in insufficient voltage to DC motor (turbocharger sub-assembly)circuit.

·

Decrease in ECM supply voltage resulting in insufficient voltage to EGR valve circuit.


·

ECM power supply circuit

·

ECM


Comes on / Does not come on*
*: Depending on the detection condition.
DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
a.

Disconnect the negative (-) battery terminal


b.

Disconnect the positive (+) battery terminal


c.

Disconnect the ECM connector.


d.

Remove the EFI MAIN NO. 1 relay from the engine room relay block and junction block.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-4 (E1) - Body ground Always Below 1 Ω
A62-5 (E2) - Body ground Always Below 1 Ω
A62-17 (E3) - Body ground Always Below 1 Ω
A62-18 (E4) - Body ground Always Below 1 Ω
A62-15 (BATT) - positive (+) battery terminal Always Below 1 Ω
A62-2 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-14 (+B2) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-1 (+B3) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-15 (BATT) or positive (+) battery terminal - Body ground Always 10 kΩ or higher
A62-2 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-14 (+B2) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-1 (+B3) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK ECM TERMINAL VOLTAGE (BATT)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK ECM TERMINAL VOLTAGE (BATT)
A325490C29
0.313,1 0.74,1.24 0.427,0.24 0.917,1.781 1.563,1.24 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.396,1.031 0.802,1.281 0.406,0.25 10 false A62 0.719,1.813 1.688,2.021 0.969,0.208 10 false BATT
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-15 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.RECHARGE OR REPLACE BATTERY
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.RECHARGE OR REPLACE BATTERY
a.

Recharge or replace the battery.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END