Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0634  Over Temperature Error  


DESCRIPTION

Refer to DTC P0045.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0045

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0634 Over Temperature Error When output terminal to DC motor circuit is overheating or supplied with too much voltage for 0.2 seconds or more.
(3 trip detection logic)
·

Open in DC motor (turbocharger sub-assembly) circuit

·

DC motor (turbocharger sub-assembly)

·

Cooling fan system

·

ECM


Comes on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF FAN HIGH SPEED AND LOW SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Fan High Speed and Actuator Test of Fan Low Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of Fan High Speed
50004 371 10
Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of Fan Low Speed
50004 371 11
OK:

Cooling fan operates according to operation.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)

NG

7.REPAIR OR REPLACE COOLING FAN SYSTEM
2.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)
a.

Disconnect the DC motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B111-1 (VN+A) - B112-51 (VN+A) Always Below 1 Ω
B111-2 (VN-A) - B112-21 (VN-A) Always Below 1 Ω
B111-1 (VN+A) or B112-51 (VN+A) - Body ground Always 10 kΩ or higher
B111-2 (VN-A) or B112-21 (VN-A) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE TURBOCHARGER SUB-ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0634)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0634)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P0634 B




A

END

B

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE COOLING FAN SYSTEM
a.

Repair or replace the cooling fan system.

Click hereEngine / Hybrid System>2WW COOLING>COOLING FAN SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END