Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P06B9  Cylinder 1 Glow Plug Circuit Range / Performance  P06BA  Cylinder 2 Glow Plug Circuit Range / Performance  P06BB  Cylinder 3 Glow Plug Circuit Range / Performance  P06BC  Cylinder 4 Glow Plug Circuit Range / Performance  


DESCRIPTION

Refer to DTC P052F.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P052F

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P06B9 Cylinder 1 Glow Plug Circuit Range / Performance Either condition is met (3 trip detection logic):
·

Malfunction in part of glow plug controller assembly which outputs to No. 1 glow plug for 1.2 seconds or more

·

Glow plug controller assembly detects resistance malfunction in No. 1 glow plug for 1.2 seconds or more


·

Glow plug controller assembly

·

No. 1 glow plug

·

Open or short in No. 1 glow plug circuit


Does not come on DTC stored
P06BA Cylinder 2 Glow Plug Circuit Range / Performance Either condition is met (3 trip detection logic):
·

Malfunction in part of glow plug controller assembly which outputs to No. 2 glow plug for 1.2 seconds or more

·

Glow plug controller assembly detects resistance malfunction in No. 2 glow plug for 1.2 seconds or more


·

Glow plug controller assembly

·

No. 2 glow plug

·

Open or short in No. 2 glow plug circuit


Does not come on DTC stored
P06BB Cylinder 3 Glow Plug Circuit Range / Performance Either condition is met (3 trip detection logic):
·

Malfunction in part of glow plug controller assembly which outputs to No. 3 glow plug for 1.2 seconds or more

·

Glow plug controller assembly detects resistance malfunction in No. 3 glow plug for 1.2 seconds or more


·

Glow plug controller assembly

·

No. 3 glow plug

·

Open or short in No. 3 glow plug circuit


Does not come on DTC stored
P06BC Cylinder 4 Glow Plug Circuit Range / Performance Either condition is met (3 trip detection logic):
·

Malfunction in part of glow plug controller assembly which outputs to No. 4 glow plug for 1.2 seconds or more

·

Glow plug controller assembly detects resistance malfunction in No. 4 glow plug for 1.2 seconds or more


·

Glow plug controller assembly

·

No. 4 glow plug

·

Open or short in No. 4 glow plug circuit


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - GLOW PLUG)
a.

Disconnect connectors of the glow plug controller assembly.


b.

Remove the glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B121-4 (GL1) - k2-1 (GLW1) Always Below 1 Ω
B121-1 (GL2) - k3-1 (GLW2) Always Below 1 Ω
B121-6 (GL3) - k4-1 (GLW3) Always Below 1 Ω
B121-5 (GL4) - k5-1 (GLW4) Always Below 1 Ω
B121-4 (GL1) or k2-1 (GLW1) - Body ground Always 10 kΩ or higher
B121-1 (GL2) or k3-1 (GLW2) - Body ground Always 10 kΩ or higher
B121-6 (GL3) or k4-1 (GLW3) - Body ground Always 10 kΩ or higher
B121-5 (GL4) or k5-1 (GLW4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE GLOW PLUG

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE GLOW PLUG
a.

Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
OK
NG



OK

END

NG

4.REPLACE GLOW PLUG CONTROLLER ASSEMBLY
4.REPLACE GLOW PLUG CONTROLLER ASSEMBLY
a.

Replace the glow plug controller assembly.

Click hereEngine / Hybrid System>2WW STARTING>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END