Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P052F  Glow Plug Control Module 1 System Voltage  


DESCRIPTION

The glow plug controller assembly has a built-in voltage output stage during glow plug activation. The ECM activates the glow plugs by sending a signal indicating the required temperature to the glow plug controller assembly.

Also, the ECM sends control signals to the glow plug controller assembly via the LIN bus based on the values from various sensors.

When the glow plug control controller assembly detects a problem in the pre-heat system, it sends a report to the ECM via the LIN bus. The malfunction report is then stored inside the ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P052F Glow Plug Control Module 1 System Voltage When glow plug controller assembly power supply voltage is low for 1.2 seconds or more.
(3 trip detection logic)
·

Glow plug controller assembly

·

Open or short in glow plug controller assembly circuit

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A365975E02
1.271,0.448 1.583,0.646 0.313,0.198 10 false SI 1.115,0.844 1.542,1.083 0.427,0.24 10 false GND 1.146,1.24 1.573,1.479 0.427,0.24 10 false GL1 1.146,1.865 1.573,2.104 0.427,0.24 10 false GL2 1.146,2.51 1.573,2.75 0.427,0.24 10 false GL3 1.146,3.156 1.573,3.396 0.427,0.24 10 false GL4 1.219,3.771 1.646,4.01 0.427,0.24 10 false +B 1.083,4.448 1.51,4.688 0.427,0.24 10 false BATT 1.51,0.448 1.927,0.646 0.417,0.198 10 false B121 1.5,0.854 1.917,1.052 0.417,0.198 10 false B121 1.594,1.24 2.01,1.438 0.417,0.198 10 false k1 1.604,1.875 2.021,2.073 0.417,0.198 10 false k1 1.594,2.51 2.01,2.708 0.417,0.198 10 false k1 1.583,3.156 2,3.354 0.417,0.198 10 false k1 1.583,4.448 2,4.646 0.417,0.198 10 false k1 1.5,3.781 1.917,3.979 0.417,0.198 10 false B121 1.635,0.26 1.979,0.438 0.344,0.177 10 false 3 1.625,0.667 1.969,0.844 0.344,0.177 10 false 2 1.635,1.052 1.979,1.229 0.344,0.177 10 false 4 1.625,1.677 1.969,1.854 0.344,0.177 10 false 1 1.625,2.313 1.969,2.49 0.344,0.177 10 false 6 1.625,2.948 1.969,3.125 0.344,0.177 10 false 5 1.625,3.573 1.969,3.75 0.344,0.177 10 false 1 1.635,4.25 1.979,4.427 0.344,0.177 10 false 7 2.99,1.135 3.333,1.313 0.344,0.177 10 false 1 3.01,1.771 3.354,1.948 0.344,0.177 10 false 1 3.01,2.417 3.354,2.594 0.344,0.177 10 false 1 3,3.063 3.344,3.24 0.344,0.177 10 false 1 2.677,1.479 3.094,1.677 0.417,0.198 10 false k2 2.885,1.49 4.104,1.75 1.219,0.26 10 false No. 1 Glow Plug 2.906,2.125 4.125,2.385 1.219,0.26 10 false No. 2 Glow Plug 2.906,2.75 4.125,3.01 1.219,0.26 10 false No. 3 Glow Plug 2.896,3.406 4.115,3.667 1.219,0.26 10 false No. 4 Glow Plug 2.677,2.115 3.094,2.313 0.417,0.198 10 false k3 2.667,2.75 3.083,2.948 0.417,0.198 10 false k4 2.667,3.406 3.083,3.604 0.417,0.198 10 false k5 5.646,0.448 6.063,0.646 0.417,0.198 10 false B112 5.646,0.854 6.063,1.052 0.417,0.198 10 false B112 5.74,0.25 6.156,0.448 0.417,0.198 10 false 74 5.729,0.656 6.146,0.854 0.417,0.198 10 false 96 6.042,0.448 6.458,0.646 0.417,0.198 10 false LIN 6.042,0.865 6.573,1.083 0.531,0.219 10 false EGCU 2.979,3.938 3.74,4.177 0.76,0.24 10 false EFI NO. 2 2.271,5.052 4.031,5.365 1.76,0.313 10 false Glow Plug Relay Assembly 4.208,4.604 4.969,4.844 0.76,0.24 10 false GLOW 0.104,4.927 2.094,5.26 1.99,0.333 10 false Glow Plug Controller Assembly 2.938,4.635 3.281,4.813 0.344,0.177 10 false 2 2.948,4.344 3.292,4.521 0.344,0.177 10 false 3 3.698,4.344 4.042,4.521 0.344,0.177 10 false 4 3.698,4.635 4.042,4.813 0.344,0.177 10 false 1 3.99,6.594 4.635,6.99 0.646,0.396 10 false EFI MAIN NO. 1 3.833,6.167 4.177,6.344 0.344,0.177 10 false 2 4.646,5.885 4.99,6.063 0.344,0.177 10 false 3 4.646,6.177 5.01,6.344 0.365,0.167 10 false 1 3.844,5.875 4.188,6.052 0.344,0.177 10 false 5 5.677,6.26 6.094,6.458 0.417,0.198 10 false A62 5.75,6.052 6.167,6.25 0.417,0.198 10 false 9 6.052,6.271 6.583,6.49 0.531,0.219 10 false MREL 6.229,7.146 6.76,7.365 0.531,0.219 10 false ECM 2.594,6.146 3.24,6.573 0.646,0.427 10 false EFI MAIN NO. 1 0.427,6.323 1.135,6.563 0.708,0.24 10 false FL MAIN 0.563,6.917 1.271,7.156 0.708,0.24 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT GLOW PLUG RELAY ASSEMBLY
a.

Inspect the glow plug relay assembly.

Click hereEngine / Hybrid System>2WW STARTING>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK GLOW PLUG CONTROLLER ASSEMBLY (BATT)

NG

12.REPLACE GLOW PLUG RELAY ASSEMBLY
2.CHECK GLOW PLUG CONTROLLER ASSEMBLY (BATT)
A351164C02
0.281,1.135 0.615,1.375 0.333,0.24 2.802,1.74 2.208,1.458 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 0.375,1.177 0.667,1.385 0.292,0.208 10 false k1 2.844,1.729 3.427,1.938 0.583,0.208 10 false BATT
*a Front view of wire harness connector
(to Glow Plug Controller Assembly)


a.

Disconnect the glow plug controller assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
k1-7 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK GLOW PLUG CONTROLLER ASSEMBLY (POWER SOURCE CIRCUIT)

NG

9.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - RELAY - BATTERY)
3.CHECK GLOW PLUG CONTROLLER ASSEMBLY (POWER SOURCE CIRCUIT)
A351158C24
0.313,1.125 0.698,1.365 0.385,0.24 0.927,1.781 1.344,1.271 false 0.177,0.177 0.49,0.333 0.313,0.156 10 false *a 0.354,1.167 0.854,1.438 0.5,0.271 10 false B121 0.719,1.781 1.219,2.052 0.5,0.271 10 false +B
*a Front view of wire harness connector
(to Glow Plug Controller Assembly)


a.

Disconnect the glow plug controller assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B121-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - EFI MAIN NO. 1 RELAY)
4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - ECM)
a.

Disconnect the glow plug controller assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B121-2 (GND) - B112-96 (EGCU) Always Below 1 Ω
B121-2 (GND) or B112-96 (EGCU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE GLOW PLUG CONTROLLER ASSEMBLY

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE GLOW PLUG CONTROLLER ASSEMBLY
a.

Replace the glow plug controller assembly.

Click hereEngine / Hybrid System>2WW STARTING>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
OK
NG



OK

END

NG

7.REPLACE ECM
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - EFI MAIN NO. 1 RELAY)
a.

Disconnect the glow plug controller assembly connector.


b.

Remove the EFI MAIN NO. 1 relay from the engine room and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B121-1 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
B121-1 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK ECM POWER SOURCE CIRCUIT

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - RELAY - BATTERY)
a.

Disconnect the glow plug controller assembly connector.


b.

Remove the glow plug relay assembly.


c.

Remove the EFI MAIN NO. 1 relay from the engine room and junction block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
k1-7 (BATT) - 3 (glow plug relay holder) Always Below 1 Ω
4 (glow plug relay holder) - positive (+) battery terminal Always Below 1 Ω
2 (glow plug relay holder) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
1 (glow plug relay holder) - Body ground Always Below 1 Ω
k1-7 (BATT) or 3 (glow plug relay holder) - Body ground Always 10 kΩ or higher
4 (glow plug relay holder) or positive (+) battery terminal - Body ground Always 10 kΩ or higher
2 (glow plug relay holder) or 3 (EFI MAIN relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK ECM POWER SOURCE CIRCUIT

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.CHECK ECM POWER SOURCE CIRCUIT
a.

Check the ECM power source circuit.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>ECM Power Source Circuit

HINT:

If there are no malfunctions in the ECM power source circuit, recharge or replace the battery.



Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE GLOW PLUG RELAY ASSEMBLY
a.

Replace the glow plug relay assembly.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END