Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1034  Throttle Valve Permanent Positive Governor Deviation  


DESCRIPTION

Refer to DTC P0122.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0122

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1034 Throttle Valve Permanent Positive Governor Deviation Either condition is met (3 trip detection logic):
·

The actual opening angle continuously deviates from the control target value of the throttle valve by 5% or more for 4 seconds.

·

The actual opening angle continuously deviates from the control target value of the throttle valve by -5% or more for 4 seconds.


The above condition occurs 4 times.
·

Diesel throttle body assembly

·

Open or short in diesel throttle body assembly circuit


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DIESEL THROTTLE BODY ASSEMBLY
a.

Check for excessive dirt or a mechanical malfunction in the diesel throttle body assembly.

OK:

No mechanical malfunction or excessive dirt.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

NG

6.REPAIR OR REPLACE DIESEL THROTTLE BODY ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
o1-1 (VC) - B112-83 (VCTA) Always Below 1 Ω
o1-3 (VTA) - B112-117 (VTA1) Always Below 1 Ω
o1-2 (E2) - B112-81 (ETA) Always Below 1 Ω
o1-4 (M+) - B112-50 (M+) Always Below 1 Ω
o1-5 (M-) - B112-20 (M-) Always Below 1 Ω
o1-1 (VC) or B112-83 (VCTA) - Body ground Always 10 kΩ or higher
o1-3 (VTA) or B112-117 (VTA1) - Body ground Always 10 kΩ or higher
o1-2 (E2) or B112-81 (ETA) - Body ground Always 10 kΩ or higher
o1-4 (M+) or B112-50 (M+) - Body ground Always 10 kΩ or higher
o1-5 (M-) or B112-20 (M-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
A351163C06
0.323,1.052 0.667,1.281 0.344,0.229 1.396,1.781 1.896,1.208 false 2.625,1.802 2.24,1.219 false 0.469,0.344 0.781,0.542 0.313,0.198 10 false *a 0.417,1.083 0.729,1.281 0.313,0.198 10 false o1 1.271,1.781 1.583,1.979 0.313,0.198 10 false E2 2.563,1.792 2.875,1.99 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Diesel Throttle Body Assembly)


a.

Disconnect the diesel throttle body assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
o1-1 (VC) - o1-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace diesel throttle body assembly.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Repair or replace the diesel throttle body assembly.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END