Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1551  Plausibility Error for Oil Pressure Sensor  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1551 Plausibility Error for Oil Pressure Sensor When the engine coolant temperature is 24.96°C (76.93°F) or higher with the engine speed 500 rpm or higher, it is detected for 6.5 seconds that the oil pressure condition is the same as that with the engine stopped.
(3 trip detection logic)
·

Oil pressure system

·

Open or short in engine oil pressure switch assembly circuit

·

Engine oil pressure switch assembly

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P1551 OPSW (Oil Pressure)

WIRING DIAGRAM

A311424E04
1.74,1.49 4.333,1.802 2.594,0.313 10 false Engine Oil Pressure Switch Assembly 1.74,1.333 2.281,1.646 0.542,0.313 10 false B118 3.344,0.813 3.885,1.125 0.542,0.313 10 false S 3.594,0.813 4.135,1.125 0.542,0.313 10 false 1 5.125,0.802 5.667,1.115 0.542,0.313 10 false 120 5.448,0.917 5.99,1.229 0.542,0.313 10 false OSW 5.781,1.938 6.323,2.25 0.542,0.313 10 false B112 5.792,2.104 6.333,2.417 0.542,0.313 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (OPSW (OIL PRESSURE))
NOTICE:
·

Since the engine is stopped due to fail-safe operation when P1551 is detected, clear the DTCs once.

·

If the Active Test cannot be performed, proceed to the inspection in the next step.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / OPSW (Oil Pressure).

Powertrain > Engine and ECT > Data List
Tester Display
OPSW(Oil Pressure)
50003 371 168

d.

Read the value.


e.

Start the engine and check that the OPSW (Oil Pressure) display changes to OFF.

OK:

Changes to OFF after the engine starts.



HINT:

When the ignition switch is turned to ON, the OPSW (Oil Pressure) display normally changes to ON, and then changes to OFF once the engine starts.


Result:
Proceed to
OK
NG



OK

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SWITCH ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SWITCH ASSEMBLY - ECM)
a.

Disconnect the engine oil pressure switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B118-1 (S) - B112-120 (OSW) Always Below 1 Ω
B118-1 (S) or B112-120 (OSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK OIL PRESSURE

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK OIL PRESSURE
NOTICE:

Since the engine is stopped due to fail-safe operation when P1551 is detected, clear the DTCs once.



Result:
Proceed to
OK
NG



OK

4.REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY

NG

7.REPAIR OR REPLACE PART CAUSING OIL PRESSURE DECREASE
4.REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY
a.

Replace the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>2WW LUBRICATION>OIL PRESSURE SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P1551)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P1551)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P1551 B




A

END

B

6.REPLACE ECM
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE PART CAUSING OIL PRESSURE DECREASE
a.

Repair the part that is causing the decrease in oil pressure.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END