The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.
The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2564 | Turbocharger Boost Control Position Sensor "A" Circuit Low | Short to ground or nozzle vane position sensor (turbocharger sub-assembly) output voltage is 0.1 V or less for 0.05 seconds.
(3 trip detection logic) |
·
Open or short in nozzle vane position sensor (turbocharger sub-assembly) circuit ·
Nozzle vane position sensor (turbocharger sub-assembly ·
ECM |
Comes on | DTC stored |
| P2565 | Turbocharger Boost Control Position Sensor "A" Circuit High | Short to +B or nozzle vane position sensor (turbocharger sub-assembly) output voltage is 4.85 V for 0.05 seconds.
(3 trip detection logic) |
·
Open or short in nozzle vane position sensor (turbocharger sub-assembly) circuit ·
Nozzle vane position sensor (turbocharger sub-assembly) ·
ECM |
Comes on | DTC stored |
When replacing the ECM, the ECM needs registration and initialization.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION
When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the nozzle vane position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B111-4 (VTA1) - B112-80 (VTAI) | Always | Below 1 Ω |
| B111-5 (VNVC) - B112-65 (VNVC) | Always | Below 1 Ω |
| B111-3 (VNE2) - B112-112 (VNE2) | Always | Below 1 Ω |
| B111-4 (VTA1) or B112-80 (VTAI) - Body ground | Always | 10 kΩ or higher |
| B111-5 (VNVC) or B112-65 (VNVC) - Body ground | Always | 10 kΩ or higher |
| B111-3 (VNE2) or B112-112 (VNE2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Nozzle Vane Position Sensor (Turbocharger Sub-assembly)) |
Disconnect the nozzle vane position sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B111-5 (VNVC) - B111-3 (VNE2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the turbocharger sub-assembly.
Click hereEngine / Hybrid System>2WW INTAKE / EXHAUST>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2564 or P2565 | A |
| No DTC output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT